Onkyo D-407M Bruksanvisning
Les nedenfor 📖 manual på norsk for Onkyo D-407M (8 sider) i kategorien Høyttaler. Denne guiden var nyttig for 2 personer og ble vurdert med 5.0 stjerner i gjennomsnitt av 1.5 brukere
Side 1/8
En Ct
Before using this unit En-2
使用本系統之前
Ct-2
Precaution on use
En-2
使用注意事項
Ct-2
Connection
En-2
連接
Ct-2
Placement
En-3
安放
Ct-3
Installation using
commercially-available
stands and fixtures
En-3
用市場銷售的支架和夾具進行
安裝時
Ct-3
Attaching and detaching
the speaker grilles
En-3
揚聲器前格板的安裝和拆除
Ct-3
Use with a TV set
En-3
作為電視機的外接揚聲器
使用時
Ct-3
Speaker care
En-3
揚聲器的維護保養
Ct-3
Specifications
En-4
規格
Ct-4
Instruction Manual
Thank you for your purchase of the Onkyo speaker
system.
Please read this manual thoroughly before using it.
Following the instructions in this manual will enable you
to obtain optimum performance and listening enjoyment
from your new speaker system.
Please retain this manual for future reference.
使用手冊
謝謝閣下購買 Onkyo 的揚聲器系統。
在連接各部件及接通電源之前， 請先徹底閱讀本手冊。
遵從本手冊內的各項指示， 使您的揚聲器系統能夠獲得
最優秀的性能和欣賞效果， 您將能獲得最大樂趣。
請保存此手冊以備將來參考之用。
D-407M
Speaker System
En-2
Connection
• Turn the sound volume to the minimum and disconnect the
power cord from the amplifier before connecting the
speaker cables.
• The nominal impedance of this speaker system is 6 Ω. Use
only amplifiers capable of handling this impedance.
• Use the supplied speaker cables to connect between
speaker’s input terminals and the amplifier’s speaker
terminals as illustrated below.
• Connect the speaker cables securely to the terminals, with
the core wires twisted properly. In this case, make sure that
the core wires do not touch each other. Note that a short
circuit in core wires may result in damage to the amplifier.
Before using this unit
• The speaker cabinet is made of wood and is therefore
sensitive to extreme temperatures and humidity. Avoid
placing the speaker systems in locations subjected to
direct sunlight, or in smoky or in humid places, such as
near an air conditioner, humidifier, bathroom, or kitchen.
Doing so may result in damage to the speaker.
• Place the unit on a rigid, level surface. Placing it on a
slanted surface or weak base not only may cause the unit
to fall, but also results in decreased sound quality.
• Be sure to turn off your amplifier before connecting the
speaker system. Connecting them with the amplifier’s
power on may result in damage to the amplifier or the
speaker system.
• Keep water or other liquids away from the unit. If water is
spilled into the unit, not only the unit but also the speakers
themselves may be damaged.
Precaution on use
• This speaker system can handle the specified input power
when it is used for ordinary music reproduction. If the
following abnormal signals are fed to the speaker,
however, an overcurrent may flow in the internal circuits,
causing burning or breakage of the wires even if the input
power is below the specified rating.
1. Noise produced when FM station is not tuned in
2. Sound produced when fast-forwarding cassette tape
deck
3. High-frequency sound generated by an oscillator, an
electronic musical instruments, etc.
4. Oscillating amplifier signals
5. Special test signals produced by audio checking CD,
etc.
6. Sound produced when connecting or disconnecting
audio connection cables (Always turn off the amplifier’s
power before connecting or disconnecting cables.)
7. Howling when a microphone is used
• Do not place magnetic objects such as screwdrivers and
iron parts near the tweeter since they use speakers with
strong magnets. Otherwise, the objects may be attracted,
causing injury or damaging the diaphragm.
Before turning on the amplifier’s power switch:
• Make sure that the positive (+) and negative (–) speaker
cables do not contact each other. Otherwise, a short-circuit
may occur, causing damage to the amplifier.
• Be sure to connect the speaker cables with correct polarity
(connect the speaker’s positive (+) and negative (–)
binding posts with the amplifier’s corresponding speaker
terminals). Reversed polarity results in impaired bass-
range reproduction, causing mislocalization of the sound
image. Also, be sure to connect the Right and Left
speakers with the amplifier’s corresponding speaker
terminals.
• Pull lightly on the speaker cables to ensure that they are
connected firmly.
Connecting to AV amplifier
RL
15mm
1. Strip off the end
of plastic skin,
and give a twist
to the core wire.
2. Slacken the
screw and thread
the core wire
deep enough into
the hole.
3. Hold the core wire
tight by fastening
the screw in the
direction of an
arrow.
Right hand side
speaker (R Channel)
Left hand side speaker
(L Channel)
Red cord side
Red cord side
Speaker terminals of the amplifier
Produkspesifikasjoner
| Merke: | Onkyo |
| Kategori: | Høyttaler |
| Modell: | D-407M |
Trenger du hjelp?
Hvis du trenger hjelp med Onkyo D-407M still et spørsmål nedenfor, og andre brukere vil svare deg
Høyttaler Onkyo Manualer
11 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
Høyttaler Manualer
- Russound
- Titanwolf
- Mackie
- Sennheiser
- Sharper Image
- Logilink
- MyDJ
- Advance Acoustic
- Bose
- Fender
- Turbosound
- Denon
- Worx
- Tracer
- Boston Acoustics
Nyeste Høyttaler Manualer
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025