Vango Hampton 800 Bruksanvisning
Les nedenfor 📖 manual på norsk for Vango Hampton 800 (1 sider) i kategorien Full. Denne guiden var nyttig for 4 personer og ble vurdert med 4.8 stjerner i gjennomsnitt av 2.5 brukere
Side 1/1
IF YOU HAVE ANY PROBLEMS PLEASE CONTACT YOUR LOCAL RETAILER or
AMG Group Ltd., Kelburn Business Park, Port Glasgow, Scotland. PA14 6TD.
UK Consumer Hotline: 0844 811 0535 E-Mail: info@vango.co.uk
Calls to our Customer Hotline cost 5p per minute. Calls from mobile phones, cable networks or public payphones will generally cost more.
FLYSHEET FIRST PITCHING
Assemble the poles and lay them parallel on the
ground.
Open out flysheet and position in required direction.
Insert the poles through the pole sleeves on the
outside of the flysheet, matching the colour of the
middle pole section to the coloured tab at the pole
sleeve end.
Locate one end of each pole on one side of flysheet
into the Ring & Pin system at the base of the tent.
Make sure poles locate into correct pin system (all
poles follow corresponding flysheet seams to pin
system).
Push poles into an arch from opposite ends and locate
pole ends into corresponding metal pin.
Tighten the tension adjusters located on the Ring & Pin
webbing.
Start pegging out the main corners at one end of the
tent using the pin pegs provided.
Pull the tent forward until taut and peg out the main
corners at the other end of the tent, again with the pin
pegs.
Ensure the tent is in a straight line.
Secure the tent using the pin pegs through the Ring &
Pin system (see fig 2).
Peg out ALL guy lines, ensuring that they are in line
with the pole or seam they are attached to.
INNER ATTACHMENT
Suspend the inner/s by attaching toggles
on the inner/s tent through rings on the
inside of the flysheet. Do the rear first and
work towards the front of the tent.
Once fully attached, the inner/s can be left
in when pitching or striking the tent.
However, it is advisable to remove the
inner/s when striking the tent when wet.
TENSION BAND SYSTEM
Remove Tension Band System from pockets
and attach into the corresponding clips at
the apex of the pole. Adjust the straps until
they are taut.
DO NOT OVER TENSION. Excess tension will
alter the shape of the tent.
Tension bands are designed to stabilise the
tunnel structure of the tent. The bands are
not required to be used in calm weather.
Figure 1.
Figure 2.
Tent Pitching Instructions Hampton 600 & 800 –
Ring & Pin System
1. Locate one end of each pole onto the corresponding metal pin. The metal pin inserts into the hollow
metal ferrule on the end of each pole. (See Figure 1). Push the pole into a curve from the opposite
side, one at a time, and locate all pole ends onto the metal pins.
2. Peg the corners of the tent through the metal rings using pin-pegs. It is important to drive the peg
into the ground at a 45 degree angle to obtain the best grip. (See Figure 2).
Produkspesifikasjoner
| Merke: | Vango |
| Kategori: | Full |
| Modell: | Hampton 800 |
Trenger du hjelp?
Hvis du trenger hjelp med Vango Hampton 800 still et spørsmål nedenfor, og andre brukere vil svare deg
Full Vango Manualer
28 September 2025
27 September 2025
27 September 2025
26 September 2025
26 September 2025
26 September 2025
26 September 2025
26 September 2025
26 September 2025
26 September 2025
Full Manualer
- Platypus
- Mountain Hardwear
- Perel
- Outwell
- Coleman
- Robinhood
- Hilleberg
- Outdoor Connection
- Dometic
- Black Diamond
- LECO
- Biltema
- MSR
- IKEA
- Khyam
Nyeste Full Manualer
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025