Alpine S2-SB10 Bruksanvisning

Alpine Høyttaler S2-SB10

Les nedenfor 📖 manual på norsk for Alpine S2-SB10 (6 sider) i kategorien Høyttaler. Denne guiden var nyttig for 25 personer og ble vurdert med 3.7 stjerner i gjennomsnitt av 13 brukere

Side 1/6
#/#ALPINE
Emotion
in
Mobility
If you have purchased the ILX-670 head unit, the
Prismalink
is capable
of
LED control
by
the
Lightinglink
Software from the head unit.
If you prefer
to
control the LEDs on the enclosure by ILX-670, please see Section A).
If you prefer
to
control by the wireless
IR
remote (included) please see Section
B).
Section A
To
control the LED functions on the
Prismalink
by the ILX-670,
connect the 3-Wire adapter plug
to
the IN location on the first
(left
or
single) enclosure terminal and ensure that the terminal
switch is set
to
Position A (Left)
Connect the Red Wire
to
12V
Connect the Black Wire
to
GND
Connect the Brown Wire
to
the
Lightinglink
Brown Wire
from the
back
of
the ILX-670.
*While in Position A the remote will only function while
aimed at the ILX-670. All function while aimed at the
enclosure
IR
sensor will be Disabled while in position
A.
Section B
If you have NOT purchased the ILX-670 head unit
OR
Prefer
to
use the
IR
remote functions
for
the
Prismalink
LED control,
ensure the terminal switch is set
to
Position B
Connect the Red Wire
to
12V
Connect the Black Wire
to
GND
Leave the Brown Wire Disconnected
OUT
0
..
« Lighting Link
Olh&rCOIO(
~
□□□□
□□□
I Dynamic Mode
-
CD000
r
"'
.,
DZWILPINE
##/ALPINE
Emotion
in
Mobility
Wiring
Diagrams
20hm
Q)
@
*DVC Jumper Change from 2 Ohm to 8 Ohm
fl'
0 0
. '
..
'
--
=2Ohm
==
=
=,
0
II
'
.
+
@ @
S2-A6
0M
20hm
20hm
Q)
Q)
Q)
@
fl'
........
0 0 0 0
...
AJWA..Pfl<!;
--
=4Ohm
[3
S2-A60M
S2-A120M
..
·-
·=
I=,
<==c,,
It
'
©
@
80hm
$
Q)
fr
0 0
--
= =
=,
'
II
+
@ @
80hm
80hm
$
@
Ql
fr
0 0 0 0
ASW'Jll.PN:W:
-~
.:;
h
·~-
_::----"·
~-
c;~
=
'=:',,
A120M
S2
-
R2
-A150M
@
t
@
'
@
I
@ (ii)
*All 3 subwoofers MUST be taken out of the enclosure and wired from 2 Ohm
to
8 Ohm
(Change from Parallel to Series with the Jumper installed
on
the subwoofer)
80hm 80hm
Ql
Q)
Q)
Q)
Q)
0
0 0
0
....
:,,,,
.,
-- --
=
I=,
=
I
It
'
II
(ii) @
(ii)
I
@ (ii)
S2-A120M
I
R2-A15
0M
*All 4 subwoofers MUST be taken out of the enclosure and wired from 2 Ohm
to
8 Ohm
(Change from Parallel to Series with the Jumper installed
on
the subwoofer)
4
I
80hm
0 0
--
·-
--
'
't
I
Q)
= 2.67 Ohm*
@
80hm
Q)
Q)
Q)
0 0
--
= 2 Ohm*
~
=
=
'
@
(ii)
I
@
IMPORTANT NOTICE!
PLEASE READ FIRST BEFORE INSTALLING SPEAKERS
Congratulations on your purchase of high quality speakers from
Alpine. Your listening satisfaction is important to us. In order to
maximize and maintain peak speaker performance the following
guidelines are being provided. Please read this notice carefully
before operating the speakers.
1. Do not over-drive the amplifier. Over-driving the amplifier will
result in distortion or clipping and can damage any speaker.
2. Make sure gain controls are properly set. (Follow
instructions in amplifier owner's manual.)
3. Make sure that the speaker is properly rated for the amplifier.
4. Make sure that volume, bass, treble, equalization or
crossover settings
do
not cause the amplifier to over-drive.
Failure to follow these guidelines may result
in
burned or damaged
speaker voice coils which will void your warranty.
If further assistance is necessary, please contact
your
Alpine
authorized dealer.
68
-
00493Z64
-A (Y)

Produkspesifikasjoner

Merke: Alpine
Kategori: Høyttaler
Modell: S2-SB10

Trenger du hjelp?

Hvis du trenger hjelp med Alpine S2-SB10 still et spørsmål nedenfor, og andre brukere vil svare deg