Astralpool ZX Series Bruksanvisning
Astralpool
Vannfilter
ZX Series
Les nedenfor 📖 manual på norsk for Astralpool ZX Series (8 sider) i kategorien Vannfilter. Denne guiden var nyttig for 29 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/8
INSTALLATION AND
OPERATING INSTRUCTIO NS
Melbourne: 03 8796 8600 Gold Coast: 07 5552 2600 Perth: 08 9350 2600
Sydney: 02 9853 2100 Townsville: 07 4750 3100 sales@astralpool.com.au
Brisbane: 07 3308 5400 Adelaide: 08 8152 7600 www.astralpool.com.au
INSTALLATION AND OPERATING INSTRUCTIONS I INSTALLATION AND OPERATING INSTRUCTIONS
ZX Series Cartridge
Filter
INST 247 ZX Series Cartridge Filter 7. V0 20
2
INST 247 ZX Series Cartridge Filter 7. V0 20
3
INTRODUCTION
Congratulations on the purchase of your AstralPool ZX series cartridge filter.
The ZX series filters are made to last by utilising the best quality materials available. The tank is made from high quality
ABS plastics, capable of withstanding the harshest of environments while DuPont Remay elements are used which are
regarded by the industry as the best available. Include with this Mircoban antimicrobial coating on the elements and
you are sure to achieve one of the cleanest pools possible.
WARNING: DO NOT OVERTIGHTEN LOCKING RING AS THIS MAY CAUSE THE FILTER TO LEAK. GENTLE HAND
TIGHT IS SUFFICIENT FOR CORRECT SEALING.
INSTALLATION OF ZX SERIES
1. Ensure cartridge filter is located on a clean, stable and level base.
2. The ZX series filter has three inlet ports (from pump) and one outlet port (to pool/spa). Glue one of the 50mm slip
tails supplied into one of the inlets and second slip tail supplied into the outlet of the filter that suits the plumbing
configuration.
3. Glue in the supplied blanking cap and drain plug cap into the two remaining inlets. Allow a minimum of one hour
for glue to dry before subjecting filter to system pressures.
4. Glue water connection pipes from pump and pool return to 50mm tails supplied. (Ensure locking nut is placed on
pipe before gluing on tails.
5. Apply Teflon tape (not included) to the pressure gauge and screw into lid where indicated.
START UP INSTRUCTIONS
1. Before starting your ZX filter, make sure the cartridge is in the filter and the lid and lock ring are in place anup d
tightened.
2. Open the suction and return line valves (when fitted).
3. Start pump and open the air release valve on the filter lid 2 to 3 turns air will begin to be forced from the tank. –
Once water begins to flow from the valve, tighten to close. Check there is a good flow of water back in the pool. to
4. Clean the cartridge when the flow to the pool reduces or the pressure gauge increases by 15 20 kPa. –
Produkspesifikasjoner
| Merke: | Astralpool |
| Kategori: | Vannfilter |
| Modell: | ZX Series |
Trenger du hjelp?
Hvis du trenger hjelp med Astralpool ZX Series still et spørsmål nedenfor, og andre brukere vil svare deg
Vannfilter Astralpool Manualer
16 Desember 2024
16 Desember 2024
16 Desember 2024
16 Desember 2024
16 Desember 2024
16 Desember 2024
16 Desember 2024
Vannfilter Manualer
- Vannfilter Laica
- Vannfilter Haier
- Vannfilter Philips
- Vannfilter AEG
- Vannfilter T.I.P.
- Vannfilter FIAP
- Vannfilter Panasonic
- Vannfilter Fluval
- Vannfilter GE
- Vannfilter Eden
- Vannfilter JBL
- Vannfilter Eldom
- Vannfilter Fisher And Paykel
- Vannfilter Vonroc
- Vannfilter Aquael
- Vannfilter Scotsman
- Vannfilter Avanti
- Vannfilter Biltema
- Vannfilter Waterdrop
- Vannfilter Stiebel Eltron
- Vannfilter JANDY
- Vannfilter Platypus
- Vannfilter Pontec
- Vannfilter Heissner
- Vannfilter Puretec
- Vannfilter Oase
- Vannfilter LARQ
- Vannfilter Tunze
- Vannfilter BTI Aqua-Solutions
- Vannfilter Laguna
- Vannfilter Steinbach
Nyeste Vannfilter Manualer
16 September 2025
16 September 2025
12 September 2025
11 September 2025
10 September 2025
10 September 2025
2 September 2025
25 August 2025
20 August 2025
12 August 2025