Bogen MIC2X Bruksanvisning

Bogen Hvorfor konsoll MIC2X

Les nedenfor 📖 manual på norsk for Bogen MIC2X (3 sider) i kategorien Hvorfor konsoll. Denne guiden var nyttig for 19 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/3

MIC X2

Microphone Input

Module

Features

• Electronically-balanced

• XLR connector

• Phantom power

• Gain/Trim control

• Hi- and Lo-cut filters

• Adjustable voice enhancer

• Audio gating with threshold adjustment

• Variable signal limiter

• 4 levels of available priority

• Can be muted from higher priority modules

• Can mute lower priority modules

Printed in Taiwan. 0208

54-2079-0 R31

Specifications subject to change without notice.

Gain

Provides control over the level of input signal that can be applied to the

internal signal buses of the main unit. Allows a way to balance the input lev-

els of various devices so that the main unit controls can be set to relative-

ly uniform or optimum levels.

Gate

Controls the minimum necessary input signal level to turn the module’s out-

put on and apply signal to the main unit's buses. Clockwise rotation increas-

es the necessary signal level required to produce output as well as the sig-

nal threshold necessary to cause the module to mute other modules.

Limiter (Limit)

Sets the signal level threshold at which the module will begin to limit the

level of its output signal. Clockwise rotation will allow more output signal

before limiting, counterclockwise rotation will allow less.The limiter moni-

tors the module’s output signal level, so increasing Gain will affect when lim-

iting takes place.

Jumper Selec

Priority Level

This module can respo

Priority 1is the highe

lower priorities and is n

by Priority modules 1

Priority 3 is muted by

mutes Priority 4 modul

all higher priority modu

*The number of priority

module capacity of the

Gating

Gating can help reduce

inputs. You can disable

output when insufficie

Detection of audio for

ty modules is always act

Phantom Power

24V phantom power ca

phones when jumper i

dynamic mics.

Bus Assignment

This module can be set

can be sent to the main

Module Installation

1. Turn off all power to the unit.

2. Make all necessary jumper selections.

3. Position module in front of desired module bay

opening, making sure that the module is right-

side up.

4. Slide module on to card guide rails. Make sure

that both the top and bottom guides are

engaged.

5. Push the module in to the bay until the faceplate

contacts the unit’s chassis.

6. Use the two screws included to secure the mod-

ule to the unit.

WARNING:

Turn off power to unit and make all jumper

selections before installing module in unit.

www.bogen.com

Block Diagram

Produkspesifikasjoner

Merke:	Bogen
Kategori:	Hvorfor konsoll
Modell:	MIC2X

Trenger du hjelp?

Hvis du trenger hjelp med Bogen MIC2X still et spørsmål nedenfor, og andre brukere vil svare deg

Ditt navn*

Din e-post*

Skriv spørsmålet ditt her

Hvorfor konsoll Bogen Manualer

Bogen BAL2S Bruksanvisning

1 Mars 2025

Bogen CAM8Pro Bruksanvisning

1 Mars 2025

Bogen MIC2S Bruksanvisning

1 Mars 2025

Bogen MIC2X Bruksanvisning

1 Mars 2025

Bogen MAX1R Bruksanvisning

1 Mars 2025

Bogen LMR1S Bruksanvisning

1 Mars 2025

Bogen LMM1S Bruksanvisning

1 Mars 2025

Bogen TEL1S Bruksanvisning

1 Mars 2025

Hvorfor konsoll Manualer

Nyeste Hvorfor konsoll Manualer

Arendo Power Mixer 303085 Bruksanvisning

4 April 2025

Auna Pro 10032076 DJ-21 Bruksanvisning

3 April 2025

Power Dynamics PDM-X Series 172.652 Bruksanvisning

31 Mars 2025

Citronic Q-PAD Bruksanvisning

20 Mars 2025

Auna Pro 10032077 DJ-21 Bruksanvisning

18 Mars 2025

Citronic CDM2 2 mk II Bruksanvisning

18 Mars 2025

Omnitronic PM-202FX Bruksanvisning

5 Mars 2025

Hobart MG1532 Bruksanvisning

28 Februar 2025

Sony SRP-X100 Bruksanvisning

18 Februar 2025

Tascam Model 2400 Bruksanvisning

13 Februar 2025