Cleveland MKDT-12-T Bruksanvisning

Cleveland Kjele MKDT-12-T

Les nedenfor 📖 manual på norsk for Cleveland MKDT-12-T (10 sider) i kategorien Kjele. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/10
MODELS:
MKDT-12-T, MKDT-20-T
SE95016 Rev. 4
Operators Manual
Installation & Operation
Direct Steam Table Top Mixers
MKDT-12-T
MKDT-20-T
1333 East 179th St., Cleveland, Ohio, U.S.A. 44110
Phone: (216) 481-4900 Fax: (216) 481-3782
Visit our web site at www.clevelandrange.com
Clev elan
d
Enodis
For a complete Service Manual
refer to www.clevelandrange.com
Shut off power at main
fuse disconnect prior
to servicing.
Ensure kettle is at room
temperature and pressure
gauge is showing zero or less
prior to removing any fittings.
Inspect unit daily for
proper operation.
0
Do not fill kettle above
recommended level
marked on outside of kettle.
Surfaces may be
extremely hot! Use
protective equipment.
Keep appliance and area free
and clear of combustibles.
Stand clear of product
discharge path when
discharging hot product.
Wear protective equipment
when discharging hot product.
Do not lean on or place
objects on kettle lip.
Do not attempt to operate
this appliance during a
power failure.
Keep clear of pressure
relief discharge.
Keep hands away from
moving parts and pinch points.
SERVICING
IMPORTANT
CAUTION
DANGER
GAS APPLIANCES
For your safety
GENERAL
Installation of the unit must be accomplished by
qualified installation personnel working to all
applicable local and national codes. Improper
installation of product could cause injury or damage.
This unit is built to comply with applicable
standards for manufacturers. Included among
those approval agencies are: UL, NSF,
ASME/Ntl.Bd., CSA, ETL, CE, and others. Many
local codes exist, and it is the responsibility of the
owner/installer to comply with these codes.
INSPECTION
Before uncrating, visually inspect the unit for
evidence of damage during shipping. If damage
is noticed, do not unpack the unit, follow shipping
damage instructions.
SHIPPING DAMAGE
INSTRUCTIONS
If shipping damage to the unit is discovered or
suspected, observe the following guidelines in
preparing a shipping damage claim.
1. Write down a description of the damage or the
reason for suspecting damage as soon as it is
discovered. This will help in filling out the claim
forms later. If possible, take a polaroid picture.
2. As soon as damage is discovered or suspected,
notify the carrier that delivered the shipment.
3. Arrange for the carrier's representative to
examine the damage.
4. Fill out all carrier claims forms and have the
examining carrier sign and date each form.
INSTALLATION
The first installation step is to refer to the
SPECIFICATION SHEET or SPECIFICATION
DRAWING to determine the exact location of the
kettle.
CLEARANCE REQUIREMENTS TO
COMBUSTIBLE AND NONCOMBUSTIBLE
SURFACES:
RIGHT LEFT BACK
MKDT-12-T 0" 0" see below
MKDT-20-T 0" 0" see below
Clearance Requirements & Pour Path Drawing
16.34
416mm
8.69
221mm
19.00
483mm
12.63
321mm
19.75
502mm
10.00
221mm
22.75
578mm
19.50
495mm
INSTALLATION

Produkspesifikasjoner

Merke: Cleveland
Kategori: Kjele
Modell: MKDT-12-T

Trenger du hjelp?

Hvis du trenger hjelp med Cleveland MKDT-12-T still et spørsmål nedenfor, og andre brukere vil svare deg




Kjele Cleveland Manualer

Kjele Manualer

Nyeste Kjele Manualer