Danfoss TP5000 Si Bruksanvisning
Les nedenfor 📖 manual på norsk for Danfoss TP5000 Si (2 sider) i kategorien Termostat. Denne guiden var nyttig for 41 personer og ble vurdert med 4.6 stjerner i gjennomsnitt av 21 brukere
Side 1/2
Fig.1
TP5000 Si/TP5000 RF Si
User Instructions
Mon-Fri Sat-Sun
Fig.2
Before programming the thermostat press and release the RESET button to restart
the unit. (Fig. 1)
Setting the Clock and Day
The day and time are set in the factory and therefore it will not normally be necessary
to do this on site. Changes between summer and winter time are handled automatically
by the unit.
Accepting the Factory Pre-settings
The TP5000 Si has pre-set times already programmed in, which often suit most people
(see table below).
Note: If set up for 4 events per day, events 3 & 4 are skipped. If set up for 2 events per
day, events 2, 3, 4 & 5 are skipped and the events are re-numbered.
To adjust the factory pre-settings & set your own time and temperature
programmes
For Days 1-5 (weekdays)
a) Press PROG (Fig. 2) until the 1st pre-set time and temperature (Event 1 Days 1,2,3,4,5)
(Fig. 3).
b) Use + or – buttons (Fig. 4) to adjust the TIME (press and hold to change in 10 min
increments).
c) Use Λ or V buttons (Fig. 5) to adjust the TEMPERATURE.
d) Press PROG (Fig. 2) to move to next preset time & temp (Event 2) (Fig. 6).
e) Repeat steps b, c & d for programming Events 3, 4, 5 & 6.
For Days 6-7 (weekends)
Press •PROG (Fig. 2) to show 1st pre-set time and temperature (Event 1 Days 6-7)
(Fig. 7).
Repeat steps b, c and d above to programme time and temperature events for •
the weekend.
Returning to RUN mode
Press PROG (Fig. 2) – the colon in the LCD display will start to flash (Fig. 8).
Fig.5
Fig.4
Fig.6
Fig.7
Fig.8
Event Time Temp. °C
1 06:30 20
2 08:30 15
3 11:30 20
4 13:30 15
5 16:30 21
6 22:30 15
Event Time Temp. °C
1 07:30 20
2 09:30 20
3 11:30 20
4 13:30 20
5 16:30 20
6 22:30 15
RESET
Fig.3
Complete Shut off - Summer time
Press Λ and V together to enter thermostat mode. A frost protection symbol (snowflake in a
shield) will appear in the display . Press the down arrow ∨ once, OFF will appear in the display.
To return to automatic programming press both ∧ and ∨ together.
Produkspesifikasjoner
| Merke: | Danfoss |
| Kategori: | Termostat |
| Modell: | TP5000 Si |
Trenger du hjelp?
Hvis du trenger hjelp med Danfoss TP5000 Si still et spørsmål nedenfor, og andre brukere vil svare deg
Termostat Danfoss Manualer
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
Termostat Manualer
- Hoffman
- ACV
- ATTACK
- OJ ELECTRONICS
- EBERLE
- Nexa
- Radson
- Braeburn
- Heatmiser
- Fenix
- PECO
- THERMAFLEX
- Drayton Erie
- Buderus
- Oventrop
Nyeste Termostat Manualer
19 Oktober 2025
19 Oktober 2025
9 Oktober 2025
8 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
24 September 2025
24 September 2025
24 September 2025