Extron FF 220T Bruksanvisning
Les nedenfor 📖 manual på norsk for Extron FF 220T (17 sider) i kategorien Høyttaler. Denne guiden var nyttig for 26 personer og ble vurdert med 4.7 stjerner i gjennomsnitt av 13.5 brukere
Side 1/17
1
FF 220T • Setup Guide
This setup guide contains installation information about the Extron FF 220T Flat Field
®
speaker. This speaker is designed for use
in plenum rated ceiling spaces and can be dropped into a standard square (2-foot by 2-foot or 600 mm by 600 mm) or rectangular
(2-foot by 4-foot or 600 mm by 1200 mm with supplied cross bars) false ceiling tile space on a T-bar grid.
WARNING: May result in serious injury. Installation and service must be performed by authorized personnel only.
NOTE: The FF 220T comes in two ceiling tile configurations depending on the tile unit of measurement:
• US version (part #42-141-03) Drops into 2 x 2 (61 cm x 61 cm) or 2 x 4 (61 cm x 122 cm) —' ' ' '
suspended tile ceilings
• Metric version (part #42-141-23)
— Drops into 600 mm x 600 mm or 600 mm x 1200 mm suspended tile
ceilings
Be sure to order the correct part number as the two configurations are not interchangeable and will not
fit correctly.
Factors to Consider Before Installation
zInstallation of conduit and conduit adapters must conform to all applicable
building codes and local ordinances.
zInstallation in a plenum-rated environment requires a wire gauge of
12 AWG to 18 AWG, as shown on the right. Conduit may be required.
zIf using secondary support cables, the installer provides the cables.
Installation
1. Disconnect power — Power down all attached devices before proceeding.
2. Remove and cut ceiling tile — Remove the square ceiling tile where the FF 220T will be installed. If the ceiling has
rectangular tiles, cut the tile in half, as shown below.
Rectangular Ceiling Tile
Dr Line At aw
Halfw Pointay
Cut Material
3. Install the T-rail in a rectangular tile — When the ceiling uses rectangular
tiles, install the T-rail crosspiece into the ceiling opening up against the
cut tile, as shown on the right.
4. Transformer cover plate — Loosen, but do
not remove, the two screws on the top of
the transformer cover plate, as shown on
the right. Next, slide and remove the
transformer cover plate, which is installed
with the transformer side down.
IMPORTANT:
Refer to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
T-rail
Crosspiece
(supplied)
Ceiling Tile
Number of Wires
per Connection Point
Maximum
Wire Gauge
1 12 GAW
2 14 GAW
1 14 GAW
2 16 GAW
Wire Gauge Table
8Ω
Configuration
70 V/100 V
Configuration
Loosen, t do not remobu ve
the 2 transformer co r plate ve
screws in the 2 yhole slotke s.
Transformer Cover Plate
Produkspesifikasjoner
| Merke: | Extron |
| Kategori: | Høyttaler |
| Modell: | FF 220T |
Trenger du hjelp?
Hvis du trenger hjelp med Extron FF 220T still et spørsmål nedenfor, og andre brukere vil svare deg
Høyttaler Extron Manualer
12 Mars 2025
25 Desember 2024
16 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
Høyttaler Manualer
- Osprey
- ESX
- HK Audio
- Delvcam
- Power Dynamics
- DB Technologies
- Kicker
- AudioControl
- Fenton
- Lexon
- Bigben
- MOOOV
- Sonoro
- Schneider
- Trevi
Nyeste Høyttaler Manualer
23 Oktober 2025
21 Oktober 2025
21 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025