Futaba R7108SB Bruksanvisning

Futaba Mottaker R7108SB

Les nedenfor 📖 manual på norsk for Futaba R7108SB (24 sider) i kategorien Mottaker. Denne guiden var nyttig for 40 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF
Side 1/24
R7108SB
1M23N17499
FASSTest-2.4GHz Bidirectional Communication System / FASST(Multi-ch,7ch) -2.4GHz
S.BUS2 / S.BUS Port and 8 Channels for Conventional System Receiver
Thank you for purchasing a Futaba R7108SB FASSTest-2.4GHz compatible receiver.
The R7108SB receiver features bi-directional communication with a FASSTest
Futaba transmitter using the S.BUS2 port. Using the port an impressive array of telemetry sensors may be utilized. It also includes both standard PWM output S.BUS2
ports (1-8ch) and S.BUS output ports. The can also be switched to the R7108SB FASST(Multi-ch/7-ch) System.
Antenna
installation
tion can be set for 3-channel only.
*Be sure that when using ESCs regulated output
the capacity of the ESC must meet your usage
condition.
*Never use dry batteries for the power supply of
WKH56%DVWKH\PD\FDXVHGLI¿FXOWLHV
• Analog servos cannot be used with the R7108SB in the FASSTest
12CH / FASST High-speed mode.
• Don't connect to Extra Voltage before turning on a receiver.
and promote safe modeling Futaba has adopted a diversity antenna system.
This allows the receiver to obtain RF signals on both antennas and fly
problem-free.
FASSTest-2.4 GHz system(18 ch/12 ch mode)
FASST-2.4 GHz system (Multi-ch/7 ch mode)
S.BUS2 and S.BUS port and 8 channels for con-
ventional system receiver
• Dual antenna diversity
• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3
mm)
• Weight: 0.42 oz. (12.0 g)
• Power req uireme nt: 3.7 V to 7.4 V(Voltage
range: 3.5 V to 8.4 V)
• Battery F/S Voltage: FASSTest---It sets up with a
transmitter FASST---3.8 V
• Extra Voltage port: 0
70 V DC
6HUYRIRUFRQYHQWLRQDO
V\VWHP
/('
$QWHQQD
/LQN0RGHVZLWFK
([WUD9ROWDJH3RUW
,WLVQRWXVHGIRUDOLQN
,WFRQQHFWVZLWKWKHEDWWHU\
IRUSRZHUHWF
Ex te rn al v o lt age in put
cable of an option
LVXVHG
7KHYROWDJHRIWKHEDWWHU\
FDQEHGLVSOD\HGZLWKD
WUDQVPLWWHU
7HPSHUDWXUH
6HQVRU
6%866HUYR
6%86*\UR
+8%
&KDQQHORXWSXW
&KDQQHORXWSXW
6%86SRUW
6%ك
6%86SRUW
6%86ك
9ROWDJH
6HQVRU
9ROWDJH
6HQVRU
530
6HQVRU
$OWLWXGH
6HQVRU
$LUVSHHG
6HQVRU
6%867RRO
(Typical installation)
5HFHLYHU
Do not insert either a switch
or battery in this manner.
Hereby, Futaba Corporation declares that the radio equipment type is R7108SB in compliance with Directive 2014/53/
EU. The full text of the EU declaration of conformity is available at the following internet address:
http://www.rc.futaba.co.jp/english/dl/declarations.html
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum dis
-
tance 20cm between the radiator & your body.
French: Cet appareil radio est conforme au CNR-210 d’Industrie Canada. L’utilisation de ce dispositifest autorisée
seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit
être prêt à accepter tout brouillage radioélectrique reçu, même sice brouillage est susceptible de compromettre le fonc
-
tionnement du dispositif. Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de ray
-
onnement et votre corps.
This device, trade name Futaba Corporation, model number R7108SB, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: To assure continued FCC compliance
$Q\FKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHJUDQWHHRIWKLVGHYLFHFRXOGYRLGWKHXVHUVDXWKRULW\
to operate the equipment.
2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
The responsible party of this device compliance is:
FUTABA Corporation of America
2681 Wall Triana Hwy Huntsville, AL 35824, U.S.A.
Phone:1-256-461-9399 FAX:1-256-461-1059 E-mail: service@futabaUSA.com
$QWHQQDSDUW
6OHHYH
&RD[LDOFDEOH
Output
connector
Channel
Mode A
1
8CH
Mode B
1
7CH
Mode C
9
16CH
Mode D
9
15CH
11199
2 2 2 10 10
3 3 3 11 11
4 4 4 12 12
5 5 5 13 13
6 6 6 14 14
7/B 7 7 15 15
8/SB 8 S.BUS 16 S.BUS
Red LED
blink
1 time 2 times 3 times 4 times
*FASST mode cannot use telemetry functions.
The R7108SB is capable of changing its channel allocations as
described in the table below. This is especially important when using
the receiver in a dual receiver mode. See your transmitter operation
manual for complete details on operating in the dual receiver mode.
Turn on the receiver. [Transmitter is always OFF]
Press and hold the Link/Mode button for 5 seconds to 10
seconds.
When the LED of the receiver changes from blinking red to
blinking red with green, Link/Mode button is released.
The LED should now blink red two times in the patterns
described in the chart below.
Each press of the Link/Mode button advances the receiver to
the next mode.
When you reach the mode that you wish to operate in, press
and hold the Link/Mode button for more than 2 seconds.
When LED blinks in green with red, it is the completion of a
mode change, Link/Mode button is released.
Please cycle the receiver power off and back on again after
changing the Channel mode.
Turn on the receiver. [Transmitter is always OFF]
Press and hold the Link/Mode button for 10 seconds to 15
seconds.
When the LED begins to blink green the button may be
released.
The LED should now be blinking green in one of the patterns
described by the chart below.
( Default : FASSTest )
Each press of the Link/Mode button advances the receiver to
the next system.
When you reach the system that you wish to operate in, press
and hold the Link/Mode button for more than 2 seconds.
When the LED blinks green and red, the system change is
complete. Release the Link/Mode button.
Please cycle the receiver power off and back on again after
changing the system.
FASSTest is a bidirectional communication system between the
R7108SB receiver and FASSTest capable transmitters. Multiple
optional telemetry sensors may be connected to the S.BUS2 on the
receiver and that data is in turn displayed on the transmitter.
Link to the transmitter : FASSTest
Bring the transmitter and the receiver close to each other,
within 20 inches (half meter).
Turn on the transmitter. Place the transmitter into the receiver
linking mode.
Turn on the receiver.
The receiver will wait for the linking process to begin for 2
seconds. Following that it will return to the normal operation
mode.
When the LED of the receiver changes from blinking red to
solid green, linking is complete.
(A link waiting state is ended in 1 second.)
• Refer to the transmitter's operation manual for complete details on how
to place the transmitter into the linking mode.
• If there are many FASSTest systems turned on in close proximity, your
receiver might have difficulty establishing a link to your transmitter.
This is a rare occurrence. However, should another FASSTest
transmitter/receiver be linking at the same time, your receiver could link
to the wrong transmitter. This is very dangerous if not noticed. To avoid
the problem, we strongly recommend that you double check whether
your receiver is really under control by your transmitter.
• If the System Type of the transmitter is changed, the receiver will need
to be re-linked to the transmitter.
Link to the TMA-1 Telemetry Adapter
R7108SB has to be FASSTest.
First, a transmitter and a receiver are linked.
Transmitter is turned off.
Press and hold the Link/Mode button of R7108SB for 15 seconds.
After the R7108SB LED lights in this sequence, Red Blink -- with Red Green
Blink -- Green Blink -- Red Blink, release the Link/Mode button.
When in link mode with the R7108SB, the TMA-1 LED blinks green along with
the red LED of the receiver.
Push the TMA-1 link button as long as necessary for its LED to blink.
Completion of a link will change LED of TMA-1 green from red only for a
moment.
Please cycle the receiver power.
S.BUS2 extends S.BUS and supports bidirectional communication.
Sensors are connected to the S.BUS2 port.
Link to the transmitter : FASST
Bring the transmitter and the receiver close to each other,
within 20 inches (half meter).
Turn on the transmitter and receiver.
Link operation is performed by the Link/Mode switch.
• When using TM-8 module, it's possible to set F/S position (only 3CH).
0 to 1 sec. 1 to 2 sec. More than 2 sec.
0 sec. 1 sec. 2 sec.
Press and Hold time
No function
With TM-8
(not included in this set)
To set the F/S
position(No re-link)
Re-link(ID set) and to
set the F/S position
No function
Besides TM-8
Re-link(ID set)
*
Refer to the instruction manual of the transmitter or module used for a description
of the linking operation, F/S position setting methods and other details.
R7108SB also can use the FASST-Multi/7ch FASST mode. The mode does
not support the telemetry functions. The FASST system has a normal mode and
a high-speed mode. However, in the High-speed mode, analog servos cannot be
used.
FUTABA CORPORATION
Hobby Radio Control Business Center Sales & Marketing Department
1080 Yabutsuka, Chosei-mura, Chisei-gun, Chiba-ken, 299-4395, Japan TEL: +81-475-32-6051, FAX: +81-475-32-2915 ©FUTABA CORPORATION 2020, 6 (1)

Produkspesifikasjoner

Merke: Futaba
Kategori: Mottaker
Modell: R7108SB

Trenger du hjelp?

Hvis du trenger hjelp med Futaba R7108SB still et spørsmål nedenfor, og andre brukere vil svare deg


Mottaker Futaba Manualer

Futaba

Futaba R7108SB Bruksanvisning

29 Mars 2025

Mottaker Manualer

Nyeste Mottaker Manualer

Yamaha

Yamaha Aventage RX-A4A Bruksanvisning

9 April 2025
Yamaha

Yamaha Aventage RX-A8A Bruksanvisning

9 April 2025
Phonocar

Phonocar PH544 Bruksanvisning

6 April 2025
DJI

DJI D-RTK 3 Bruksanvisning

5 April 2025
QSC

QSC SPA-Qf 60x2 Bruksanvisning

2 April 2025
Harper

Harper HDT2-5010 Bruksanvisning

2 April 2025
Harper

Harper HDT2-2010 Bruksanvisning

2 April 2025
Streacom

Streacom TL1 Bruksanvisning

31 Mars 2025
Graupner

Graupner GR-8 Bruksanvisning

31 Mars 2025
MB Quart

MB Quart FA2-1000.1 Bruksanvisning

30 Mars 2025