NUVO 60/2625 Bruksanvisning
Les nedenfor 📖 manual på norsk for NUVO 60/2625 (1 sider) i kategorien Lettelse. Denne guiden var nyttig for 28 personer og ble vurdert med 4.8 stjerner i gjennomsnitt av 14.5 brukere
Side 1/1
INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES
YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS
REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to
follow the steps in the order given. Under no circumstances
should a fixture be hung on house electrical wires, nor should a
swag type fixture be installed on a ceiling which contains a
radiant type heating system. Read instructions carefully. If you
are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all
parts are included as shown in figure. Be careful not to misplace
any of the screws or parts, which are needed to install this
fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1: Thread the mounting screw (Not supplied) into the
match holes in the mounting bar (A).
STEP 2: Secure the mounting bar (A) to outlet box with the
outlet box screws (B).
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the mounting bar. Wrap the ground
wire from the fixture (if supplied) around the green
grounding screw, then connect it to ground wire from
the outlet box (if not fixed on the outlet box) using a
wire connector (not supplied). If ground wire from the
fixture is not supplied, wrap the ground wire (if not
fixed on the outlet box) from the outlet box around the
green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and
connect the wires according to the directions below:
GROUP A: Connect to Black
House Wire
GROUP B: Connect to White
House Wire
BLACK WHITE
*PARALLEL WIRE (round &
smooth)
*PARALLEL WIRE (square &
ridged)
WHITE OR GREY WITH
TRACER
WHITE OR GREY WITHOUT
TRACER
BROWN GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer
wire is square shaped or ridged and the less tracer wire is round
in shape or smooth (seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do NOT
twist wires together before using wire connectors.
STEP 4: Fit a wire connector (not supplied) over the wires and
screw the connector clockwise until you feel firmness.
STEP 5: Try gently to pull the connector off the wires. If you can
pull the connector off, carefully re-do steps 3 and 4 as
above, and check again for a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire
from the outlet box in the same manner. Make sure no
bare wires can be seen outside wire connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside
outlet box. Raise the canopy (C) allowing for the
mounting screws to protrude through key slots. Rotate
canopy (C) clockwise until mounting screws are in
narrow part of key slots, tighten with screwdriver.
STEP 2: Install light bulbs. (Please do not exceed the maximum
capacity recommended on the socket.).
STEP 3: Place glass (E) over nipple (D) then secure with
washer (F) and cap (G).
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to
order replacement parts. Be sure to use exact wording from
illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to these fixture.
ITEM NO: 60-2621 60-2624 60-2628
60-2622 60-2625 60-2629
60-2623 60-2627 60-2631
60-3105 60-3106 60-3107
60-3311 60-3312 60-3313
60-3335 60-3336 60-3337
Produkspesifikasjoner
| Merke: | NUVO |
| Kategori: | Lettelse |
| Modell: | 60/2625 |
Trenger du hjelp?
Hvis du trenger hjelp med NUVO 60/2625 still et spørsmål nedenfor, og andre brukere vil svare deg
Lettelse NUVO Manualer
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
Lettelse Manualer
- Busch + Müller
- Schwaiger
- DMT
- ET2
- Yongnuo
- Brandson
- HQ Power
- Maginon
- Integral LED
- Yamazen
- Canarm
- Fotodiox
- Trust
- Schonbek
- Showtec
Nyeste Lettelse Manualer
9 April 2025
9 April 2025
8 April 2025
8 April 2025
8 April 2025
7 April 2025
6 April 2025
6 April 2025
6 April 2025
6 April 2025