WAC Lighting WS-23018 Bruksanvisning

WAC Lighting Lettelse WS-23018

Les nedenfor ๐Ÿ“– manual pรฅ norsk for WAC Lighting WS-23018 (2 sider) i kategorien Lettelse. Denne guiden var nyttig for 24 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF
Side 1/2
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
๎˜ƒ
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
๎˜ƒ
1600 Distribution Ct
Lithia๎˜ƒSprings,๎˜ƒGA๎˜ƒ30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Oct. 2019 1
๎˜ƒ
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER
BEFORE BEGINNING.
โ€ Read all instructions before installing.
โ€ System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.
โ€ When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
โ€ Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by
dweLED could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.
MAINTENANCE๎˜ƒNOTE:๎˜ƒ
Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
๎˜ƒ
๎˜ƒ
MISE EN GARDE: Pour รฉviter tout choc รฉlectrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
โ€ Lisez toutes les instructions avant lโ€™installation.
โ€ Le systรจme doit รชtre installรฉ par un รฉlectricien licensiรฉ conformรฉment au code national de lโ€™รฉlectricitรฉ (NEC), et รฉgalement
aux rรจglements locaux.
โ€ Lors de la manipulation du luminaire, nโ€™appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les piรจces doivent รชtre utilisรฉes comme indiquรฉ dans ces instructions. Ce produit est conรงu pour รชtre utilisรฉ
seulement avec les piรจces et/ou accessoires fournis pour รชtre utilisรฉs avec les produits dweLED. Remplacer des piรจces ou
accessoires non conรงus pour ce produit dweLED pourrait causer des dommages corporels ou matรฉriels et pourrait รฉgalement causer
lโ€™annulation de la garantie. Veuillez contacter un revendeur autorisรฉ ou le fabricant si des piรจces manquent ou sont endommagรฉes.
NOTE๎˜ƒDโ€™ENTRETIEN:๎˜ƒ
Les conditions cรดtiรจres peut causer une accumulation de minรฉraux et de rรฉsidue sur le luminaire. Nous
recommendons aux clients qui resident dans les zones cรดtiรจres de nettoyer toutes les surfaces externes du luminaire une fois toutes
les deux semaines avec un chiffon humide.
๎˜ƒ
HARDWARE
๎˜ƒ
๎˜ƒ
Wire Connector
Qty: 3pcs+1 Extra
AB
Mounting Screw
Qty:1 Extra
5/32-32x1/2
INSTALLATION INSTRUCTIONS
220 โ€“ LED Wall Sconce
WS-22018
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
๎˜ƒ
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
๎˜ƒ
1600 Distribution Ct
Lithia๎˜ƒSprings,๎˜ƒGA๎˜ƒ30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Oct. 2019 2
๎˜ƒ
INSTALLATION INSTRUCTIONS
220 โ€“ LED Wall Sconce
WS-22018
Fig.1๎˜ƒ
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for
installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the fixture.
4. Secure the mounting back plate to the junction box using the screws provided with the junction box.
NOTE: (i) using any other non-original-manufacturer provided junction box screws may result in safety issue;
(ii) the side of the mounting plate marked โ€œGNDโ€must face out.
CONNECTING THE WIRES (Fig. 2)
5. Connect the driverโ€™s input wires to junction box wires as shown (Fig. 2). Make sure that all wire connectors (A) are secured. If
your outlet box has a green or bare copper ground wire, connect the fixtureโ€™s ground wire to it. Otherwise, connect the fixtureโ€™s
ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the
junction box.
6. Secure the fixture to the mounting back plate using the mounting screw (B).
DIMMING WIRING INFORMATION (Fig. 3)
7. This fixture features electronic low voltage (ELV or TRAIC) dimming capabilities. See notes below for specific dimming wires
information.
8. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
9. To utilize 0-10V dimming: use wir e purple (dim+), gray (dim-),black (hot), white (neutral) and bare copper ground wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the fixture in order to allow the 0-10V dimming to function properly.
Fig. Fig.๎˜ƒ ๎˜ƒ2 Wiring๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ ๎˜ƒ3
๎˜ƒ๎˜ƒ
๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ ๎˜ƒ
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare Wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
White - Neutral
Black - Hot
Purple - Dim+
Grey - Dim-
Red - Fixture+
Black - Fixture-
Back Plate Dimensions
1
3
4
"
1
3
8
"
6
5
8
"
4
3
8
"
B
A
Wire Connector
Mounting Screw
Driver
Mounting๎˜ƒ
Back๎˜ƒPlate
Junction Box
Bare Copper
Ground Wire
Black Wire
White Wire
Junction
Screw

Produkspesifikasjoner

Merke: WAC Lighting
Kategori: Lettelse
Modell: WS-23018

Trenger du hjelp?

Hvis du trenger hjelp med WAC Lighting WS-23018 still et spรธrsmรฅl nedenfor, og andre brukere vil svare deg


Lettelse WAC Lighting Manualer

WAC Lighting

WAC Lighting WS-W33118 Bruksanvisning

6 April 2025
WAC Lighting

WAC Lighting DS-WD06 Bruksanvisning

6 April 2025
WAC Lighting

WAC Lighting WS-23018 Bruksanvisning

6 April 2025
WAC Lighting

WAC Lighting DS-WD08 Bruksanvisning

6 April 2025
WAC Lighting

WAC Lighting WS-W33125 Bruksanvisning

6 April 2025
WAC Lighting

WAC Lighting DS-WS06 Bruksanvisning

6 April 2025
WAC Lighting

WAC Lighting WS-W42016 Bruksanvisning

5 April 2025
WAC Lighting

WAC Lighting WS-W21110 Bruksanvisning

5 April 2025
WAC Lighting

WAC Lighting DS-WS05 Bruksanvisning

5 April 2025
WAC Lighting

WAC Lighting DS-WD05 Bruksanvisning

5 April 2025

Lettelse Manualer

Nyeste Lettelse Manualer

ET2

ET2 Waterfall E24846-90 Bruksanvisning

9 April 2025
Schwaiger

Schwaiger CALE100 511 Bruksanvisning

9 April 2025
Ryobi

Ryobi One+ P796B Bruksanvisning

8 April 2025
ADB

ADB Orkis Fresnel Bruksanvisning

8 April 2025
Claypaky

Claypaky Actoris ParLED Bruksanvisning

8 April 2025
V-Tac

V-Tac VT-995 Bruksanvisning

7 April 2025
V-Tac

V-Tac VT-1055 Bruksanvisning

6 April 2025
Canarm

Canarm Bryant IOL598BK Bruksanvisning

6 April 2025
Dainolite

Dainolite V166-1W Bruksanvisning

6 April 2025
Dainolite

Dainolite OFE-161P Bruksanvisning

6 April 2025