NUVO NV-SUBAMP200-NA Bruksanvisning
Les nedenfor 📖 manual på norsk for NUVO NV-SUBAMP200-NA (14 sider) i kategorien Mottaker. Denne guiden var nyttig for 27 personer og ble vurdert med 4.9 stjerner i gjennomsnitt av 14 brukere
Side 1/14
Part Numbers
NV-SUBAMP100-xx
NV-SUBAMP200-xx
NV-SUBAMP500-xx
AMPLIFIER FEATURES
NV-SUBAMP100-xx
1 13 10
514 6 15 127
Fig. 1
NV-SUBAMP200-xx
19
5 12 11102071617
8
6 21415
Fig. 2
NV-SUBAMP500-xx
NOTE: Power mode, Volume control, Phase control, and Crossover control are accessed on the LCD display menu using the control knob.
19 2 3
219
12 111817 108 1020
Fig. 3
Installation Instructions
Nuvo In-Wall / In Ceiling Subwoofer Amplifiers
1507315 Rev A 20190328
2
1
Status light
2
LCD display
3
Control knob
4
Power mode switch
5
Volume control
6
Phase control
7
Crossover control
8
Low-level RCA input/
output jacks
9
USB port
10
Voltage selector switch
11
Master power switch
12
Power cord inlet
13
WLS
14
High-level input
15
EQ selection:
A - NV-SUBIC8
B - NV-SUBIW8
C - SUBIWDUAL8
16
EQ mode
17
12 V DC trigger input/
output
18
IR
19
Power button
20
Sub terminal screws
21
Fuse
This instruction sheet covers the installation of the Nuvo In-Wall/In-Ceiling Subwoofer Amplifiers. These amplifiers offer a substantial amount of dynamic
power to increase the quality of your audio system.
UNDERSTANDING THE LCD PANEL FEATURES (FOR NV-SUBAMP500-XX MODELS)
Power Up Screen
Shows a message that the system is powering up.
Home Screen/Volume
Option for adjusting volume level.
Audio Mode Screen/Status
This setting has presets to put the amplifier into a mode that supports
your favorite listening environment. Choose one of the following options:
• Music
• Movie
• Bypass
Night Mode Status
This setting places a low sound threshold on the system for evening use.
• Off
• On
Speaker EQ Screen
Select one of the following modes:
• NVSUBIC8 1
• NVSUBIW8 2
• NVSUBIWDUAL8 3
• Flat
3
Crossover Main Screen
Crossover provides an option for a low pass filter for the amplifier. Choose
from one of the following options:
• LFE (Default setting)
• 40 - 250 HZ
Phase Screen
• 0-180
Lock Control Main Screen
Locks the menu for the amplifier controls to prevent accidental changes.
• Off
• On
Factory Reset
• Yes: Resets all amplifier controls to the default settings.
• No
Power Options Screen
This setting sets the power state. Choose from one of the following options:
• The amplifier is always on. This is the default setting.Switch:
• 12 V Trigger: The amplifier turns on automatically upon receiving a 12 V
input signal. When the 12 V signal is removed, the amplifier automatically
goes into standby mode.
• The amplifier turns on automatically upon receiving an Audio Sensor:
audio input signal. When the amplifier no longer receives a signal, it
automatically moves into a standby state after 15 minutes.
IR - Device ID
Assigns an IR ID between 1 and 4 to the amplifiers in the system.
• 1
• 2
• 3
• 4
Exit Menu Screen
• Press the knob to exit the menu for the controls and bring up the Home/
Volume screen.
Produkspesifikasjoner
| Merke: | NUVO |
| Kategori: | Mottaker |
| Modell: | NV-SUBAMP200-NA |
Trenger du hjelp?
Hvis du trenger hjelp med NUVO NV-SUBAMP200-NA still et spørsmål nedenfor, og andre brukere vil svare deg
Mottaker NUVO Manualer
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
Mottaker Manualer
- Focal
- Max
- Yamaha
- Neumann
- Sunfire
- Marantz
- JL Audio
- Reely
- Deaf Bonce
- CYP
- Shure
- CSL
- Triax
- Fiio
- Graupner
Nyeste Mottaker Manualer
30 September 2025
30 September 2025
30 September 2025
30 September 2025
30 September 2025
30 September 2025
30 September 2025
29 September 2025
29 September 2025
29 September 2025