NUVO Warren 60/8037 Bruksanvisning
Les nedenfor 📖 manual på norsk for NUVO Warren 60/8037 (2 sider) i kategorien Lettelse. Denne guiden var nyttig for 23 personer og ble vurdert med 4.4 stjerner i gjennomsnitt av 12 brukere
Side 1/2
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES
YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS
REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this xture. Be sure to follow
the steps in the order given. Under no circumstances should a
xture be hung on house electrical wires, nor should a swag type
xture be installed on a ceiling which contains a radiant type heating
system. Read instructions carefully. If you are unclear as to how to
proceed, consult a qualied electrician.
NOTE: Proper wiring is essential for the safe operation of this xture.
FIXTURE ASSEMBLY
Carefully remove the xture from the carton and check that all parts
are included as shown in gure. Be careful not to misplace any of
the screws or parts, which are needed to install this xture.
STEP 1: Thread tube. Carefully pass the wires through each tube
during assembly. Repeat this step until the desired hanging height
is reached.
STEP 2: Thread the tube into the canopy and body.
INSTALLATION
IMPORTANT: Do not attach xture directly to outlet box.
STEP 1: Thread mounting screw into the matching hole of mounting
bracket.
STEP 2: Secure the cross bar to outlet box with outlet box screws.
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the mounting bar. Wrap the ground wire from the
xture (if supplied) around the green grounding screw, then connect it
to ground wire from the outlet box (if not xed on the outlet box) using
a wire connector (not supplied). If ground wire from the xture is not
supplied, wrap the ground wire (if not xed on the outlet box) from the
outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your xture. Identify
which group your xture wire(s) falls into and connect the wires
according to the directions below:
GROUP A:
Connect to Black House Wire
GROUP B:
Connect to White House Wire
BLACK WHITE
* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is
square shaped or ridged and the less tracer wire is round in shape
or smooth (seen best when viewed from wire end.)
STEP 3: Take your xture wire(s) from group A and place evenly
against the black wire from the outlet box. Do NOT twist wires
together before using wire connectors.
STEP 4: Fit a wire connector over the wires and screw the
connector clockwise until you feel rmness.
STEP 5: Try gently to pull the connector off the wires. If you can
pull the connector off, carefully re-do steps 3 and 4 as above, and
check again for a rm connection.
STEP 6: Connect the xture wire from group B to the white wire
from the outlet box in the same manner. Make sure no bare wires
can be seen outside wire connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside outlet
box. Raise canopy allowing the mounting screw to protrude through
the hole in the canopy, and secure with ball nuts.
STEP 2: Thread nipple into the xture. Adjust the hex nut to a
proper position.
STEP 3: Install lamps (not included). Please do not exceed the
maximum capacity recommended on the socket.
STEP 4: Secure glass to the xture with decorative nut.
CLEANING
To clean, wipe xture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Be sure to use exact wording from illustration
when ordering parts.
Line art shown may not exactly match the xture enclosed. However, the installations
do apply to this xture.
La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,
las instalaciones sí aplican para esta pieza.
Les images peuvent ne pas correspondre exactement au luminaire de la boîte.
Par contre, les directives d’installation s’appliquent au luminaire.
© Copyright 2024 Satco Products, Inc. 4/24 v2.0
ITEM NO: 60-8037
ARTÍCULO Nº: 60-8037
ARTICLE N°: 60-8037
INSTALLATION AND SAFETY INSTRUCTIONS
FIGURE
Produkspesifikasjoner
| Merke: | NUVO |
| Kategori: | Lettelse |
| Modell: | Warren 60/8037 |
Trenger du hjelp?
Hvis du trenger hjelp med NUVO Warren 60/8037 still et spørsmål nedenfor, og andre brukere vil svare deg
Lettelse NUVO Manualer
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
Lettelse Manualer
- Brennenstuhl
- Light4Me
- Livex Lighting
- Smith-Victor
- Fluval
- Singercon
- Infinity
- Olight
- Triton Blue
- Eheim
- Bresser
- Yongnuo
- Bora
- Ledlenser
- Currey & Company
Nyeste Lettelse Manualer
9 April 2025
9 April 2025
8 April 2025
8 April 2025
8 April 2025
7 April 2025
6 April 2025
6 April 2025
6 April 2025
6 April 2025