PAC RP3-GM11 Bruksanvisning
PAC
Ikke kategorisert
RP3-GM11
Les nedenfor 📖 manual på norsk for PAC RP3-GM11 (2 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 20 personer og ble vurdert med 4.8 stjerner i gjennomsnitt av 10.5 brukere
Side 1/2
RP3-GM11
Radio Replacement Interface for General Motors Vehicles
Pacifi c Accessory Corporation
®
| Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacifi c Accessory Corporation
www.pac-audio.com
Rev. 120513
3
3
Introduction & Features
Important Notes
Wiring Connection Chart
Illustration / Schematic
The RP3-GM11 interface allows the replacement of a factory radio in select General Motors vehicles with Class II radios. Using
this interface will retain factory features such as Warning Chimes and BOSE® amplifi er (Standard or Premium) when the original
radio is removed. The RP3-GM11 provides data bus driven outputs such as retained accessory power (RAP), vehicle speed
sensor (VSS), illumination, reverse trigger and parking brake. The RP3-GM11 also provides a secondary output for adding an
optional PAC Steering Wheel Control (SWC) retention interface (SWI-RC, SWI-PS, SWI-JACK, SWI-ECL2 or SWI-X). Rear Seat
Controls (RSC) if equipped will also be retained with the SWI interface.
1. When used in Non-BOSE® applications simply cut off the RCA connectors and connect the remaining wires to the aftermarket
radios high level speaker outputs.
2. For BOSE® systems, the recommended line level input is between 2-4 volts from the aftermarket radio.
3. RSC buttons that are identical to the SWC will mimic the SWC one for one
4. To prevent over driven audio when installing the interface into a vehicle with a BOSE® system, and the aftermarket radio does
not have low level outputs, then an LOC (part # SOEM-4 or LP3-4) is recommended to match the input voltage or you can create
an audio attenuation circuit (see diagram 2 below for audio attenuation wiring).
5. Use the 4 position selector switch located on the side of the interface to select the best chime output volume for your specifi c
installation .
Red / White Parking Brake
Output (-)*
Purple / White Vehicle Speed
Output*
Blue / White Amp Turn On Input
Red Accessory Output
(10 amp)
Orange / White Illumination Output
(+)*
Green Reverse Output (+)*
Interface Connector
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Vehicle Connector
Audio Attenuation Circuit for RP3-GM11
One channel shown
*Not all radios will have these
connections. Please insulate
these wires when not used.
Diagram 1
Chime Volume Adjustment
Cut for Non-Bose systems
Aftermarket Radio
Connections
To Vehicle
Connector
Connect to SWC
Interface. Program
for Version 2.
To optional SWC interface
Acc On
LED
Produkspesifikasjoner
| Merke: | PAC |
| Kategori: | Ikke kategorisert |
| Modell: | RP3-GM11 |
Trenger du hjelp?
Hvis du trenger hjelp med PAC RP3-GM11 still et spørsmål nedenfor, og andre brukere vil svare deg
Ikke kategorisert PAC Manualer
3 August 2025
3 August 2025
3 August 2025
3 August 2025
3 August 2025
10 Mars 2025
19 Februar 2025
19 Februar 2025
19 Februar 2025
19 Februar 2025
Ikke kategorisert Manualer
Nyeste Ikke kategorisert Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025