Palmer PW9V Bruksanvisning
Les nedenfor 📖 manual på norsk for Palmer PW9V (2 sider) i kategorien Lader for mobil enhet. Denne guiden var nyttig for 25 personer og ble vurdert med 4.9 stjerner i gjennomsnitt av 13 brukere
                        Side 1/2
                    
                    
                    
SAFETY INFORMATION
1.  Please read these instructions carefully. 
2.  Keep all information and instructions in a safe place. 
3.  Follow the instructions. 
4.  Observe  all  safety  warnings.  Never  remove  safety  warnings  or  other  information  from 
the equipment. 
5.  Use the equipment only in the intended manner and for the intended purpose. 
6.  Use only sufciently stable and compatible stands and/or mounts (for xed installations). 
Make certain that wall mounts are properly installed and secured. Make certain that the 
equipment is installed securely and cannot fall down. 
7.  During installation, observe the applicable safety regulations for your country. 
8.  Never install  and operate  the equipment  near radiators,  heat registers,  ovens or  other 
sources of heat. Make certain that the equipment is always installed so that is cooled 
sufciently and cannot overheat. 
9.  Never place sources of ignition, e.g., burning candles, on the equipment. 
10.  Ventilation slits must not be blocked. 
11.  Do not use this equipment in the immediate vicinity of water (does not apply to special 
outdoor equipment - in this case, observe the special instructions noted below. Do not 
expose this equipment to ammable materials, uids or gases. 
12.  Make certain that dripping or splashed water cannot enter the equipment. Do not place 
containers lled with liquids, such as vases or drinking vessels, on the equipment. 
13.  Make certain that objects cannot fall into the device. 
14.  Use this equipment only with the accessories recommended and intended by the man
-
ufacturer. 
15.  Do not open or modify this equipment. 
16.  After connecting the equipment,  check all  cables in order to prevent damage or acci
-
dents, e.g., due to tripping hazards. 
17.  During transport, make certain that the equipment cannot fall down and possibly cause 
property damage and personal injuries.
18.  If your equipment is no longer functioning properly, if uids or objects have gotten inside 
the equipment or if it has been damaged in another way, switch it off immediately and 
unplug it from the mains outlet (if it is a powered device). This equipment may only be 
repaired by authorized, qualied personnel. 
19.  Clean the equipment using a dry cloth. 
20.  Comply with all applicable disposal laws in your country. During disposal of packaging, 
please separate plastic and paper/cardboard. 
21.  Plastic bags must be kept out of reach of children.
For equipment that connects to the power mains:
22.  CAUTION: If the power cord of the device is equipped with an earthing contact, then it 
must be connected to an outlet with a protective ground. Never deactivate the protective 
ground of a power cord. 
23.  If the equipment has been exposed to strong uctuations in temperature (for example, af
-
ter transport), do not switch it on immediately. Moisture and condensation could damage 
the equipment. Do not switch on the equipment until it has reached room temperature. 
24.  Before connecting the equipment to the power outlet, rst verify that the mains voltage 
and frequency match the values specied on the equipment. If the equipment has a volt
-
age selection switch, connect the equipment to the power outlet only if the equipment 
values and the mains power values match. If the included power cord or power adapter 
does not t in your wall outlet, contact your electrician. 
25.  Do not step  on the  power cord. Make certain that  the power cable does not  become 
kinked,  especially  at  the  mains  outlet  and/or  power  adapter  and  the  equipment  con
-
nector. 
26.  When connecting the equipment, make certain that the power cord or power adapter is 
always freely accessible. Always disconnect the equipment from the power supply if the 
equipment is not in use or if you want to clean the equipment. Always unplug the power 
cord and power adapter from the power outlet at the plug or adapter and not by pulling 
on the cord. Never touch the power cord and power adapter with wet hands. 
27.  Whenever possible, avoid switching the equipment on and off in quick succession be
-
cause otherwise this can shorten the useful life of the equipment.
28.  IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. 
If a fuse blows repeatedly, please contact an authorised service centre. 
29.  To disconnect the equipment from the power mains completely, unplug the power cord 
or power adapter from the power outlet. 
30.  If your  device is equipped with a Volex power connector, the mating Volex equipment 
connector must be unlocked before it can be removed. However, this also means that the 
equipment can slide and fall down if the power cable is pulled, which can lead to person
-
al injuries and/or other damage. For this reason, always be careful when laying cables. 
31.  Unplug the power cord and power adapter from the power outlet if there is a risk of a 
lightning strike or before extended periods of disuse.
caution: 
CA UT IO N
RI SK OF   SELE CTRI C HO CK
DO  N  O NOT PE
Never remove the cover, because otherwise there may be a risk of electric shock. There are 
no user serviceable parts inside. Have repairs carried out only by qualied service personnel. 
The lightning ash with arrowhead symbol within an equilateral triangle is intended to 
alert the user to the presence of uninsulated “dangerous voltage” within the product’s 
enclosure that may be of sufcient magnitude to constitute a risk of electrical shock. 
The exclamation mark within an equilateral triangle is intended to alert the user to the 
presence of important operating and maintenance instructions.
caution – hiGh VoLume LeVeLs with auDio proDucts!
This equipment  is intended  for professional  use. Therefore, commercial use of this equip
-
ment is subject to the respectively applicable national accident prevention rules and regula-
tions. As a manufacturer, Adam Hall is obligated to notify you formally about the existence of 
potential health risks. Hearing damage due to high volume and prolonged exposure: When 
in use, this product is capable of producing high sound-pressure levels (SPL) that can lead 
to irreversible hearing damage in performers, employees, and audience members. For this 
reason, avoid prolonged exposure to volumes in excess of 90 dB. 
caution! important inFormation aBout LiGhtinG proDucts
1.  Do not look into the beam from a distance of less than 40 cm. 
2.  Do not stare into the beam for extended periods at short-to-medium distances. 
3.  Do not view the beam directly with optical instruments such as magniers.
4.  Under some circumstances, stroboscopic effects may trigger epileptic seizures in sen
-
sitive individuals! For this reason, persons who suffer from epilepsy should always avoid 
places where strobe lights are used.
MANUFACTURER’S WARRANTY 
This warranty extends to the Palmer branded product you purchased from Adam Hall. The 
statutory warranty rights against the vendor shall not be affected by this warranty. Rather, this 
warranty gives you additional independent claims against Adam Hall.
With this warranty, Adam Hall ensures that products you have purchased from Adam Hall or 
Adam Hall partners, under normal use, are free of defects in material or workmanship for a 
period of 5 years from the date of purchase, or 2 years from the date of purchase for tube 
ampliers and guitar cabinets. The warranty period begins on the date of purchase. In order 
to assert a claim for warranty service, the proof of date of purchase is provided by the receipt 
bearing the date of purchase or the date of purchase on the delivery note. You are entitled 
to warranty service under the conditions and provisions set out in this document, if a repair 
within the warranty period is required.
This warranty applies only to the original purchaser of the products supplied by Adam Hall 
and is not transferable to any person to whom the property is transferred by the original pur-
chaser. Within the warranty period, the defective parts or the product from Adam Hall will be 
repaired or replaced. Under the terms of this warranty, all the replaced or removed compo
-
nents become the property of Adam Hall. In the unlikely event that a product acquired from 
Adam Hall, repeatedly exhibits a defect, Adam Hall may decide, at its discretion, to replace 
this product with a comparable product of at least the same performance.
Adam  Hall  does  not  guarantee  that  the  operation  of  this  product  will  be  uninterrupted  or 
error-free. Adam Hall accepts no responsibility for any damage due to incorrect compliance 
with the instructions received in the delivery. 
This warranty does not extend to:
• wearing parts (eg battery, tubes).
• devices that have had their serial number removed or damaged, or failed as a result of 
an accident
• inappropriate or abusive use or other external causes
• devices that were not used in accordance with the operating parameters dened in the 
user documentation shipped with the product
• devices that have been repaired using parts not made or distributed by Adam Hall
• devices that have been serviced, modied or repaired by someone other than Adam Hall 
or an authorised service partner.
These terms and conditions constitute the complete and exclusive warranty agreement be
-
tween you and Adam Hall regarding the Adam Hall branded product you have purchased.
This warranty is valid only within Europe. Outside of Europe please contact our ofcial dis
-
tributors.
LIMITATION OF LIABILIT Y 
If your Adam Hall branded hardware product fails to work as warranted above, your sole and 
exclusive remedy shall be repair or replacement. Adam Halls’ maximum liability under this 
limited warranty is expressly limited to the lesser of the price you have paid for the product 
or the cost of repair or replacement of any components that malfunction under conditions 
of normal use.
Adam Hall is not liable for any damages caused by the product or the failure of the product, 
including any lost prots or savings or special, incidental, or consequential damages. Adam 
Hall is not liable for any claim made by a third party or made by you for a third party.
This limitation  of liability  applies whether  damages are sought, or claims are made, under 
this Limited Warranty or as a tort claim (including negligence and strict product liability), a 
contract claim, or any other claim, and  cannot  be  rescinded  or  changed  by  anyone.  This 
limitation of liability will be  effective even if  you have advised  Adam Hall  or an authorized 
representative of Adam Hall of the possibility of any such damages, but not, however, in the 
event of claims for damages in connection with personal injuries.
This  manufacturer’s  warranty  grants  you  specic  rights;  depending  on  jurisdiction  (nation 
or state), you may be be entitled to additional claims. You are advised to consult applicable 
state or national laws for a full determination of your rights. 
requestinG warrantY serVice 
To request warranty service for the product, contact Adam Hall or the Adam Hall authorized 
reseller from which you purchased the product.
ec DecLaration oF conFormit Y 
The equipment  marketed by Adam  Hall complies (where applicable) with  the essential re
-
quirements and other relevant specications of Directives 1999/5/EC (R&TTE), 2004/108/EC 
(EMC) und 2006/95/EC (LVD). Additional information can be found at www.adamhall.com.
         proper DisposaL oF this proDuct 
(waste eLectricaL anD eLectronic equipment) 
(Valid in the European Union and other European countries with waste separation) 
This symbol on the product, or the documents accompanying the product, indicates that this 
appliance may not be treated as household waste. This is to avoid environmental damage or 
personal injury due to uncontrolled waste disposal. Please dispose of this product separately 
from other waste and have it recycled to promote sustainable economic activity.
Household  users  should contact either the retailer where they purchased  this  product,  or 
their local government ofce, for details on where and how they can recycle this item in an 
environmentally friendly manner. 
Business users should contact their supplier and check the terms and conditions of the pur
-
chase contract. This product should not be mixed with other commercial wastes for disposal 
enVironmentaL protection anD enerGY conserVation 
Energy conservation is an active contribution to environmental protection. Please turn off all 
unneeded electrical devices. To prevent unneeded devices from consuming power in stand
-
by mode, disconnect the mains plug. 
OPERATION/CONNECTION
Regard the safety information stated above. 
Be sure that the polarity of connected device matches that of this power supp
This power supply can deliver a DC voltage of Volts at a maximum current of 500 mA. 
Be sure not to overload the power supply. This power supply is equipped with a DC 
connector measuring 2.1 x 5.5 mm. Be sure that the socketof the connected end 
device  matches  to  the  connector.  Be  sure  the  end  device  is  turned  off  whilst  making  the 
connection.Disconnect this device from the mains when not in use
TECHNICALSPECIFICATIONS
Product type:   power supply
Type:     switchmode power supply
mains connector:   IEC connector
input voltage:   100 - 240 V
Outputs:     1
output connectors:  2.1 x 5.5 mm
output voltage:   9 V
max. output current:   500 mA
polarity:     center negative
cord length:     150 cm
Width:     70 mm
depth:     30 mm
height:     70 mm
Weight:    0,19 kg
Since all our products are constantly controlled and improved, technical changes are 
possible without prior notice.
PW9V
Standard 9V Power Supply
© Palmer Musical Instruments, Adam Hall GmbH, D-61267 Neu-Anspach, Daimlerstr. 9, Germany TEL: ++49 (0)6081 94190
FAX: ++49 (0)6081 43280 WEB: www.adamhall.com, www.palmer-germany.com EMAIL: info@palmer-germany.com
Produkspesifikasjoner
| Merke: | Palmer | 
| Kategori: | Lader for mobil enhet | 
| Modell: | PW9V | 
Trenger du hjelp?
Hvis du trenger hjelp med Palmer PW9V still et spørsmål nedenfor, og andre brukere vil svare deg
Lader for mobil enhet Palmer Manualer
                        
                         16 Oktober 2024
                        
                    
                                                            
                        
                         16 Oktober 2024
                        
                    
                                                            
                        
                         16 Oktober 2024
                        
                    
                                                            
                        
                         16 Oktober 2024
                        
                    
                                                            Lader for mobil enhet Manualer
- XD-Design
- Mophie
- IKEA
- RayNeo
- Belkin
- SKROSS
- Leba
- Aukey
- V7
- Götze & Jensen
- Sitecom
- NOCO
- Ansmann
- Urban Revolt
- Xuma
Nyeste Lader for mobil enhet Manualer
                        
                         3 April 2025
                        
                    
                                                            
                        
                         2 April 2025
                        
                    
                                                            
                        
                         2 April 2025
                        
                    
                                                            
                        
                         29 Mars 2025
                        
                    
                                                            
                        
                         29 Mars 2025
                        
                    
                                                            
                        
                         28 Mars 2025
                        
                    
                                                            
                        
                         14 Mars 2025
                        
                    
                                                            
                        
                         14 Mars 2025
                        
                    
                                                            
                        
                         14 Mars 2025
                        
                    
                                                            
                        
                         11 Mars 2025