Royer Labs dBooster2 Bruksanvisning
Royer Labs
Mikrofon
dBooster2
Les nedenfor 📖 manual på norsk for Royer Labs dBooster2 (2 sider) i kategorien Mikrofon. Denne guiden var nyttig for 33 personer og ble vurdert med 3.7 stjerner i gjennomsnitt av 17 brukere
Side 1/2
Royer Labs
Professional Audio Products
dBooster2
dBooster2
dBooster2
dBooster2 dBooster2
Stereo in-line Microphone and DI (Direct Injection) Signal Booster
With the introduction of the original , low-output passive microphones could be boosted with up dBooster
to 20dB of clean signal boost and superior sound quality. The takes that concept to the next dBooster2
level.
The Royer model is a phantom powered two-channel in-line level booster/buer for passive low-R-DB22
output ribbon and dynamic microphones and incorporates a high-impedance Direct Injection input for
guitars and other Hi-Z sources.
An integrated combination input jack accommodates standard 3-Pin microphone XLR inputs and ¼-inch
high-impedance inputs. The dBooster2 is designed for professional applications and provides two levels
of clean boost in both the low-impedance microphone mode; 12dB or 20dB and the high-impedance mode;
0dB (unity) or 8dB, selectable by a front panel switch.
How to set up your dBooster2
NOTE: It is a good idea to make all of your connections before activating phantom power and turning up
your preamp level control!
One of the unique features of the is that each channel of this stereo unit is completely isolated dBooster2
from the other. They are completely independent. This minimizes the chance of ground loops developing
when used with stereophonic microphones or dierent independent channels of microphone preampliers
and interfaces.
The goes between any non-powered ribbon or dynamic mic, ¼ Hi-Z source and your preamp, dBooster2
DAW or audio interface. In the mic mode it will provide either 12dB or 20dB of signal boost for low-output
microphones. In the Hi-Z DI (direct injection) mode it will deliver unity gain (0-dB) or +8dB of gain. A
front panel switch establishes the gain setting.
When used for microphones, the microphone is connected to the INPUT of the via a standard dBooster2
3-conductor XLR microphone cable. In the DI mode the source is connected via a standard two-conductor
¼-inch guitar type cable. The
OUTPUT of the is dBooster2
connected to any preamplier, DAW
or interface that is enabled with
phantom power capability.
The is a mic-level device dBooster2
and not intended to drive line-level
inputs directly. After your
connections are made, apply
phantom-power, and slowly bring up
the preamp level to verify that the
microphone or DI input is passing
signal. To achieve the best
performance from your dBooster2
with minimal noise and distortion at
Produkspesifikasjoner
| Merke: | Royer Labs |
| Kategori: | Mikrofon |
| Modell: | dBooster2 |
Trenger du hjelp?
Hvis du trenger hjelp med Royer Labs dBooster2 still et spørsmål nedenfor, og andre brukere vil svare deg
Mikrofon Royer Labs Manualer
13 Februar 2025
24 Oktober 2024
24 Oktober 2024
Mikrofon Manualer
- Kurzweil
- Monacor
- Auna
- Asus
- Sanken
- Antelope
- Max
- Neewer
- Hollyland
- Louroe Electronics
- Insignia
- Prodipe
- Mojave
- Radial Engineering
- Røde
Nyeste Mikrofon Manualer
18 Oktober 2025
18 Oktober 2025
17 Oktober 2025
16 Oktober 2025
15 Oktober 2025
15 Oktober 2025
15 Oktober 2025
13 Oktober 2025
13 Oktober 2025
13 Oktober 2025