Satco S18412 Bruksanvisning
Les nedenfor 📖 manual på norsk for Satco S18412 (4 sider) i kategorien Følge. Denne guiden var nyttig for 25 personer og ble vurdert med 4.1 stjerner i gjennomsnitt av 13 brukere
Side 1/4
1
LED T8 U-BEND LAMPS
Model: S18412
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing xture. Retain for future reference.
Item Number-Description Overall Dimensions (mm) Operating Temperature CCT Volts
S18412-13T8 /U3/L ED/CCT/BP 92 x 562.1 x 572.3 –20ºC ~ 45ºC 30K, 40K, 50K 120V–277V
WARNING
• DANGER: Risk of shock-disconnect power before
installation.
• WARNING: Risk of re or electric shock. The
electrical rating of these products are 120-277Vac,
the installer must determine whether they have
120-277Vac at the luminaire before installation.
• WARNING: Risk of re or electric shock.
LED Retrot Kit installation requires knowledge of
luminaire electrical systems. If not qualied, do not
attempt installation. Contact a qualied electrician.
• WARNING: Product must be installed in
accordance with the national electrical code or
your local electrical code. If you are not familiar with
these codes and requirements, contact a qualied
electrician.
• WARNING: Install this kit only in luminaries that
have the construction features and dimensions
shown in the photographs and/or drawing and
where the input rating of the retrot kit does not
exceed the input rating of the luminaire.
• WARNING: To prevent wiring damage or abrasion,
do not expose wiring to edges of sheet metal or
other sharp objects.
• WARNING: To avoid potential re or shock hazard,
do not use this retrot kit in luminaries employing
shunted bi-pin lampholders. NOTE: Shunted lamp
holders are found only in uorescent luminaries
with instant-start ballasts. Instant-start ballasts can
be identied by the words “Instant Start” or “I.S.”
marked on the ballast. This designation may be in
the form of a statement pertaining to the ballast
itself, or may be combined with the marking for
the lamps with which the ballast is intended to be
used, for example F40T 12/IS, for more information
contact the LED luminaire retrot kit manufacturer.
Do not make or alter any open holes in an
enclosure of wiring or electrical components during
kit installation.
Installers should not disconnect the existing wire
from lampholder terminals to make new connections
at lampholder terminals. Instead installers should cut
existing lampholder leads away from the lampholder
and make new electrical connections to lampholder
lead wires by employing applicable connectors.
• WARNING: Luminaire wiring and electrical
parts may be damages when installing retrot
kit hardware. Check for enclosed wiring and
components.
• WARNING: Check the existing wiring for damage
before installing upgrade kit. Do not install if existing
wires are damaged.
This retrot kit is accepted as a component of a
luminaire where the suitability of the combination
shall be determined by authorities having
jurisdiction.
Type B Lamp – this LED tube is intended to replace
uorescent tube lamps with ANSI designation.
• Do not use with dimmers.
• Suitable for damp locations.
• Not for emergency lighting.
Satco Products, Inc.
Brentwood, NY 11717© Copyright 2023 Satco Products, Inc. 1/23 v1.2
Produkspesifikasjoner
| Merke: | Satco |
| Kategori: | Følge |
| Modell: | S18412 |
Trenger du hjelp?
Hvis du trenger hjelp med Satco S18412 still et spørsmål nedenfor, og andre brukere vil svare deg
Følge Satco Manualer
31 Mars 2025
31 Mars 2025
31 Mars 2025
31 Mars 2025
31 Mars 2025
31 Mars 2025
31 Mars 2025
31 Mars 2025
30 Mars 2025
30 Mars 2025
Følge Manualer
- Christie
- Feelworld
- Peerless-AV
- Yealink
- Cocopar
- TCL
- Vimar
- KeepOut
- Delvcam
- Freedom Scientific
- Simrad
- KRK
- Soundstream
- Prestigio
- Postium
Nyeste Følge Manualer
9 April 2025
9 April 2025
8 April 2025
8 April 2025
5 April 2025
5 April 2025
3 April 2025
2 April 2025
30 Mars 2025
29 Mars 2025