Simrad Fuel Flow Sensor Bruksanvisning
Simrad
Ikke kategorisert
Fuel Flow Sensor
Les nedenfor 📖 manual på norsk for Simrad Fuel Flow Sensor (2 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 15 personer og ble vurdert med 3.5 stjerner i gjennomsnitt av 8 brukere
Side 1/2
*988-10714-001*
Whats in the box
A
C
B
D
E
Fuel Flow Sensor
Installation Guide
Tools required Overview
Plan the installation
Use one Fuel Flow Sensor for each engine
Plan the installation
Mount to vibration free surface with the flow direction arrow
pointing upwards.
Mount as close as possible to the fuel tank
Plan the installation
Mount the sensor above the tank’s maximum fuel level to avoid
accidental fuel leakage in case the sensor becomes disconnected.
Sharp knife for cutting fuel line
Screw driver for tightening hose
clamp
The Fuel Flow was designed to fit a
typical 3/8” SAE USCG Type A1 fuel
hose. If your engine has different
diameter hoses or metal fuel lines,
a section of 3/8” fuel line must be
installed between the sensor and the
existing lines.
Stainless steel hose clamps
Cable ties for securing Fuel Flow
Sensor
The Fuel Flow Sensor is a device for measuring the flow rate of fuel
for gasoline powered boats.
!
The Fuel Flow Sensor is designed for gasoline engines
only.
The Fuel Flow Sensor does not operate diesel engine fuel sys-
tems, or on any fuel system with a return fuel line or sump.
Other parts required
Fuel Flow Sensor
Micro-C T-Joiner
A Drop Cable 3 m (10 ft)
B Male Micro-C connector
D Fuel Flow sensor: Arrow indicates fuel flow direction
C Fuel line connector (3/8”): To engine
E Fuel line connector (3/8”): From tank
A Fuel Flow sensor: Arrow indicates fuel flow direction
B Fuel Filters: One before each fuel sensor
C Fuel Tank
Before commencing the installation
Caution:
Gasoline is extremely ammable. If possible, drain the fuel
line before you start or shut any ow valves located at the
tank. Keep sparks and ame away from the work area. After
installation, remember to clean up any spilled fuel.
!DANGER
No Smoking
No Open Flames
No Sparks
Fuel Filter
You must install an in-line fuel lter between the tank and the
Fuel Sensor sensor. This will prevent a malfunction caused
by contaminated fuel. Debris in unltered fuel can clog the
sensor’s turbine and result in rough performance or engine
shut down.
As with any fuel system, we recommend you always carry
onboard a spare fuel lter and an in-line (3/8”) splice barb.
This allows you to remove a clogged Fuel Sensor or fuel lter
and restore engine operation if the fuel lter fails. We strongly
recommend that you inspect your entire fuel system at regular
intervals.
Mount vertically
To engine
From tank
Fuel ow
direction
A
B
C
Max fuel tank level
Fuel Flow Sensor
Gasoline
Fuel lter
Produkspesifikasjoner
| Merke: | Simrad |
| Kategori: | Ikke kategorisert |
| Modell: | Fuel Flow Sensor |
Trenger du hjelp?
Hvis du trenger hjelp med Simrad Fuel Flow Sensor still et spørsmål nedenfor, og andre brukere vil svare deg
Ikke kategorisert Simrad Manualer
8 April 2025
2 April 2025
2 April 2025
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
Ikke kategorisert Manualer
- Master
- Sheeran Looper
- Oregon Scientific
- Doona
- Fujifilm
- Induction Dynamics
- Perixx
- Cadel
- AGM
- Ridem
- Quantum
- Ergotron
- LiveU
- Bebob
- Mebby
Nyeste Ikke kategorisert Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025