Sonance Bandpass BPS6 Bruksanvisning

Sonance Subwoofer Bandpass BPS6

Les nedenfor 📖 manual på norsk for Sonance Bandpass BPS6 (2 sider) i kategorien Subwoofer. Denne guiden var nyttig for 19 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF
Side 1/2
Determine the location for the mounting platform.
Ensure there is adequate room for the BPS6
subwoofer at the location of the platform.
The speaker opening must be located within
12” (305mm) of the BPS6 to allow the port
tube to reach through the platform.
Place the mounting template on the side of
the joist and drill four 1/2” (12.7mm) holes
through the joist at the locations shown on
Attach the mounting platform to the joists.
See mounting platform quickstart guide or visit
www.sonance.com/in-wall-in-ceiling/
architectural-series for detailed
installation manual.
Hold the side of the BPS6 with the rubber
damping pad up against the side of the joist
and install the four lag screws and washers to
secure the BPS6 in place.
3 4
1
12” (305mm)
BPS6
Port tube
2
(1) Quickstart guide
(1) Bandpass subwoofer w/ port tube
(1) Cardboard mounting template
Mounting screws & washers:
(4) 5/16” x 2” lag screws (for thinner beams)
(4) 5/16” x 3” lag screws (for thicker beams)
(4) 5/16” washers
Box Contents
Bandpass subwoofer can be installed in joists spaced 16” on center or greater.
AS BANDPASS STEREO SUBWOOFER QUICKSTART GUIDE
BPS6
SONANCE ARCHITECTURAL SERIES
®
©2014 Sonance. All rights reserved.
Sonance and Architectural Series are registered trademarks of Dana Innovations.
Due to continuous product improvement, all features and specifications are subject to change without notice.
For the latest Sonance product specification information, visit our website: www.sonance.com
SONANCE • 212 Avenida Fabricante • San Clemente, CA 92672-7531 USA
(800) 582-7777 or (949) 492-7777 • FAX: (949) 361-5151 • Technical Support: (800) 582-0772
www.sonance.com
06.05.1433-5946
On the end of the BPS6 port tube there is a tether.
The tether will be used later to guide the BPS6 port
tube through the mounting platform opening.
Position end of port tube as close as possible
to back of mounting platform. Loop tether into
the anchored zip tie and secure. This process
ensures that bandpass connector is easily
attached later and other tradespersons won’t
infringe on port tube assembly area.
5 6
7 8
Tether into
zip tie
Tether
detailed eManual scan
the QR code or visit
www.sonance.com/
in-wall-in-ceiling/
architectural-series
Secure the wires with a zip tie near the
terminals to prevent accidental removal by
another tradesperson.
Attach the from the four conductor wires
amplifier to the input terminals on the end of
the BPS6. Positive wires to red terminals and
negative wires to black terminals. Run the
speakers wires to amplifier location and run
signal test with 9V battery. NOTE: Port tube
contains foam plug with tether, make sure
pressure levels don’t expel the foam and
tether. Do not connect the voice coils
in parallel.

Produkspesifikasjoner

Merke: Sonance
Kategori: Subwoofer
Modell: Bandpass BPS6

Trenger du hjelp?

Hvis du trenger hjelp med Sonance Bandpass BPS6 still et spørsmål nedenfor, og andre brukere vil svare deg


Subwoofer Sonance Manualer

Sonance

Sonance Bandpass BPS6 Bruksanvisning

9 Januar 2025

Subwoofer Manualer

Nyeste Subwoofer Manualer

Phase Technology

Phase Technology IW200-II Bruksanvisning

5 April 2025
SoundTube

SoundTube CM1001D Bruksanvisning

3 April 2025
Wet Sounds

Wet Sounds ZERO 10 S4 XZ-W Bruksanvisning

2 April 2025
Phase Technology

Phase Technology PL-12p Bruksanvisning

30 Mars 2025
ETON

ETON Graphit 8-4 Bruksanvisning

20 Mars 2025
ETON

ETON PW 8 Bruksanvisning

20 Mars 2025
ETON

ETON Graphit 8-2 Bruksanvisning

19 Mars 2025
ETON

ETON Graphit 10-4 Bruksanvisning

19 Mars 2025
ETON

ETON MW 10 FLAT Bruksanvisning

19 Mars 2025
ETON

ETON USB 6 AR Bruksanvisning

19 Mars 2025