StarTech.com PEX2S953LP Bruksanvisning
StarTech.com
Ikke kategorisert
PEX2S953LP
Les nedenfor 📖 manual på norsk for StarTech.com PEX2S953LP (2 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 12 personer og ble vurdert med 4.3 stjerner i gjennomsnitt av 6.5 brukere
Side 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: December 17, 2019 9:30 AM
Product Diagram (PEX2S953LP)
Port Function
1Serial Port • Used to connect Serial Devices
2Screws
• Used to attach the to the Serial Port Bracket
• Used to secure a to the Serial Cable Serial
Port
3Bracket • Used to attach the to the Card Computer
4
PCI Express Bus
Connector
• Used to connect the PCI Express Serial Card
to the Computer’s Motherboard
5Jumper • Used to congure power settingsSerial Port
6Printed Circuit Board
• Components such as are located on Jumpers
the Board
2-Port PCI Express Serial Card with 16950 UART - Low-Prole
7LP4 Power Connector • Used to connect a Power Source
Requirements
• PCIe Slot
• Needle-Nose Pliers
For the latest requirements and full manual, please visit
www.startech.com/PEX2S953LP.
Installation
WARNING!
PCI Express Serial Cards can be severely damaged by static electricity. Make sure
that you are properly grounded before you open your or touch the Computer Case
PCI Express Serial Card Anti-Static Strap. You should wear an when you install any
computer component. If an isn’t available, discharge any built-up Anti-Static Strap
static electricity by touching a large for several seconds. Only Grounded Metal Surface
handle the by its edges and don’t touch the gold connectors.PCI Express Serial Card
Jumper Conguration
Note: Jumper Serial Devices conguration is a requirement when connecting that
require power through a . Serial Port
This can be moved into one of three dierent positions in order to set the Jumper
power output voltage for the . The default setting for the is , Serial Ports Jumpers RI
which is the setting for no power. The can be moved to one of the other two Jumper
settings for or of power. To congure the , complete the following:5V 12V Jumper
1. Locate the for . is located on the right hand side, labeled Jumper Port One Port One
as on the . The is labeled as on the COM1 Printed Circuit Board Jumper J1 Printed
Circuit Board.
2. Carefully remove the . Lift the straight up and o of the Jumper Jumper PCI Express
Serial Card.
Note: Always hold the by the edges.Card
3. Determine the power setting that is required for .Port One
4. Position the over the set of that correspond with the desired Jumper Pins Serial
Port Power Setting Jumper. See to determine where the Figure 1 should be
positioned.
5. Push the straight down and into place.Jumper
Note: Push the all the way into position for proper contact. Jumper
1 2
1 2
4
3
5
7
6
5
Produkspesifikasjoner
| Merke: | StarTech.com |
| Kategori: | Ikke kategorisert |
| Modell: | PEX2S953LP |
Trenger du hjelp?
Hvis du trenger hjelp med StarTech.com PEX2S953LP still et spørsmål nedenfor, og andre brukere vil svare deg
Ikke kategorisert StarTech.com Manualer
14 Oktober 2025
13 September 2025
18 Mars 2025
18 Mars 2025
22 Januar 2025
22 Januar 2025
22 Januar 2025
22 Januar 2025
22 Januar 2025
22 Januar 2025
Ikke kategorisert Manualer
- Giardino
- M-Audio
- Fischer
- Cramer
- Enbrighten
- Elvid
- Winix
- Atdec
- Proscan
- Monacor
- SilverStone
- Mirage
- Equator
- Toddy
- Vixen
Nyeste Ikke kategorisert Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025