Austral Super 5 Bruksanvisning
Austral
Ikke kategorisert
Super 5
Les nedenfor 📖 manual på norsk for Austral Super 5 (4 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 25 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 13 brukere
Side 1/4
Austral Clothes Hoists Pty. Ltd.
Incorporated In Victoria A.B.N.: 68 006 790 727
32-34 Hydrive Close, Dandenong South 3175, Australia
Tel: (03) 9799 8122, Fax: (03) 9799 8266
International Tel: +61 3 9799 8122, Fax: +61 3 9799 8266
www.australclotheshoists.com.au
admin@australclotheshoists.com.au
Installation Instructions for: Super & Deluxe Hoists
Your Austral Rotary Clothes Hoist is designed to last a long time. It is important to follow these instructions so you will
enjoy the benefits of a properly installed hoist. Incorrect installation could damage your hoist and/or void your guarantee.
If at any time your Austral Hoist should not function correctly or if spare parts are required call your state distributor ,
listed on the guarantee page.
Site Selection & Digging (S - teps 1 3)
Important: Before digging, ensure the area is safe and clear of electrical, gas and plumbing services etc (refer to Dial Before
You Dig (Aus), beforeUdig (NZ), any architectural drawings etc).
1 1. Select a site that gives 1m clearance to the end of each arm of the hoist (2m more than hoist’s diameter), see Figure
2 P lace Handle Shaft through Handle Grip then
tap into hole in Handle Arm whilst supporting
behind the A rm with a chock, see Figure 2.
Turn the handle anti ensure the- clockwise to
hoist is wound down as far as it goes. Also fit
Handle Cover to Deluxe models.
3 Ensure it is safe to dig at the selected site. At its centre, start digging
- a hole 150 200mm in diameter. Dig the hole deep enough so that
Cwhen the olumn is stood upright in the hole the Reducer is level with
the user’s head height, see Figure 3. A depth of 550mm will result in
the Cross being 1700mm high and the outer lines being approximately 1850mm high when
the hoist is wound down. After height is set, allow Column to lean over and rest in the hole.
3a Deluxe models only: remove the olumn frC om the hole and insert the Steel Rod through the
pre-drilled holes in the bottom of the olumn back in the hole. C Column. Place Note:
instead of Steel Rod, Super models have a crimped bottom a tube to hold firm in concrete.
Equipment Required
Spirit level, crowbar, shovel, , pliers, concrete, drainage gravel, tape measurescrewdriver
Parts Supplied
Qty
Description
Part Number
1
Rotary or Helical Column
R/COL (Super) or H/COL (Deluxe)
4
Arms ( m 1975m or 2475mm)
RH01A R06A (4m model) or ) (5m model
1
Handle Grip, Black Plastic
FRC11
1
Handle Shaft, Black Plastic
FRC12
4
Round End Caps, Black Plastic
R19
1
Wire Roll (50m or 70m)
R14 or R15
4
Tubular Stays (1500 95mm or 19 mm)
RH03A R08A (4m model) or (5m model)
4
Bolt, 35mm x 6mm
FA18
4
Bolt, 20mm x 6mm
RH04
8
Nylon Lock Nut, 6mm
FRC22
4
Washer, 6mm
R18
Deluxe Hoists only:
1
Handle Cover, Black Plastic
HE03
1
Steel Rod, 150mm x 8mm
FA24
Produkspesifikasjoner
| Merke: | Austral |
| Kategori: | Ikke kategorisert |
| Modell: | Super 5 |
Trenger du hjelp?
Hvis du trenger hjelp med Austral Super 5 still et spørsmål nedenfor, og andre brukere vil svare deg
Ikke kategorisert Austral Manualer
16 Oktober 2024
Ikke kategorisert Manualer
- Legrand
- Hughes & Kettner
- Smith-Victor
- CyberPower
- Aluratek
- MagnaPool
- Randell
- Rigol
- ARC
- Kaorka
- Morphy Richards
- Grundfos
- Audix
- Snom
- NGS
Nyeste Ikke kategorisert Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025