DeWalt DCB606 Bruksanvisning
Les nedenfor 📖 manual på norsk for DeWalt DCB606 (2 sider) i kategorien Accu. Denne guiden var nyttig for 27 personer og ble vurdert med 3.8 stjerner i gjennomsnitt av 14 brukere
Side 1/2
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (DEC06) Form No. 635693-00 Copyright © 2006 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of
pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
IF YOU HAVE ANY QUESTIONS OR COMMENTS CALL US TOLL
FREE AT:
1-800-4-DEWALT (1-800-433-9258)
JAW REPLACEMENT INSTRUCTIONS
DC495
COMPONENTS (FIG. 1)
A. Trigger switch/variable speed switch
B. Swivel head shear
C. On/Lock-off control button
D. Hex wrench
E. Battery pack
F. Battery release buttons
Disassembly and Assembly (Fig. 2–5)
WARNING: Turn unit off and disconnect battery pack before
installing and removing accessories, before adjusting or when
making repairs. To prevent inadvertant operation, lock the trigger
switch when the tool is not in use and when storing the tool.
To remove shear head from motor, loosen the two back cap
screws (G) using the hex wrench (D) provided. Remove shear head
(B) from the body by pulling head firmly forward (Fig. 2). Slight
twisting action may be required if head does not slide off easily.
To remove cutter blades from the shear head, completely loosen
the two back cap screws and remove shear head from motor unit.
Loosen the tensioning screw (O) 1/2 turn. Completely loosen all
three cap screws and remove head assembly. Turn assembly over
and remove top half of head and then remove the blades.
To replace blades, place lower jaw (P) onto two pins (R). Apply a
thin layer of grease from the packet (included) around the pin and
on the top side of the blade. Place upper jaw (Q) onto pin. Apply the
rest of the grease provided onto the eccentric (L) on the output shaft
of the motor unit and into the area behind the upper moving blade
in the shear head.
Install replacement washer (S), cone side up, over the pin on top of
the moving blade. Place top half of head back (T) onto bottom half
(U), making sure to align the pin to the hole. Reinstall all three cap
screws (G) and nuts (V), but DO NOT tighten completely.
Slide shear head back onto motor unit, making sure that the
eccentric engages the moving blade. Once the head is on the motor
unit and aligned, tighten all three screws and follow adjustment
procedure below.
To ensure proper blade tension, tighten tensioning screw (O) by
turning clockwise to seat the blades. Next, loosen tensioning screw
by turning counterclockwise slightly to allow blade movement.
NOTE: The tensioning screw should be adjusted to correspond to
material thickness.
A
E
B
C
D
F
L
FIG. 2
B
D
G
(BACK)
(DOS)
(REVERSO)
G (FRONT / AVANT / FRENTE)
O
FIG. 3
FIG. 5
N
G
P
Q
T
U
FIG. 1
FIG. 4
S
P
Q
R
Produkspesifikasjoner
| Merke: | DeWalt |
| Kategori: | Accu |
| Modell: | DCB606 |
Trenger du hjelp?
Hvis du trenger hjelp med DeWalt DCB606 still et spørsmål nedenfor, og andre brukere vil svare deg
Accu DeWalt Manualer
4 Januar 2025
24 Oktober 2024
24 Oktober 2024
16 Oktober 2024
Accu Manualer
- EGO
- Stiga
- Neewer
- Ventev
- Berg
- Venom
- Biltema
- Renata
- PAG
- APSystems
- Tecnoware
- Aim TTi
- Milwaukee
- Tripp Lite
- Ryobi
Nyeste Accu Manualer
3 April 2025
21 Februar 2025
21 Februar 2025
31 Januar 2025
30 Januar 2025
23 Januar 2025
23 Januar 2025
23 Januar 2025
23 Januar 2025
23 Januar 2025