Holosun Paralow HS403B Bruksanvisning
Holosun
Ikke kategorisert
Paralow HS403B
Les nedenfor 📖 manual på norsk for Holosun Paralow HS403B (3 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 30 personer og ble vurdert med 4.7 stjerner i gjennomsnitt av 15.5 brukere
Side 1/3
Fig 2-1
Features
Important notices
Battery
Installation
Fig1 PARALOW HS403B Red Dot Sight
www.holosun.com
HS403B
PARALOW
Thank you for purchasing the PARALOW HS403B Red Dot
sight,Please read the User's Manual carefully.
1. The HS403B projects its aiming dot in
a way that prevents visibility when viewed from the front
beyond several meters.
2. The user can gain
rapid target acquisition and situational awareness while aiming
with both eyes open.
3. Only a few micro-amperes of current
are required for sight operation. Sight runs on one battery for
up to 30,000 hours.
Concealed aiming:
Full field of view for target acquisition:
Low power consumption:
4. The sensitive motion sensor will turn the
power on with any motion detecon when in sleep mode.
5. arallax 1MOA
Motion power on:
Parallax free optical system: P is .
≤
±
6. The sight will be automatically entered into
sleep mode motionless for 8 hours.
7. There are 12 settings(10 Daylight+2NV)
for the reticle so as to match the ambient lighting conditions.
8. The sight will remember the last saved
brightness setting when powered on and off.
9 The top mounted buttons allow
Sleep time delay:
Brightness adjustment:
Memory function:
.
Two top mounted buttons:
for easy operation without obstructing the user's vision.
10. IP67 Waterproof:
1. Ensure that the firearm is completely unloaded and safe
before device installation or installing/replacing the
baery.
2. Please keep the packaging should you need to make a
warranty claim.
1.The operating voltage for this device is DC3V using one high
quality CR2032 Lithium battery.
2.The baery life is rated up to 50,000 hours at a mid-brightness
seing.
3.Baery Replacement:
Please follow the steps below for battery replacement
1. The included mount is
compatible with Picatinny Rails.
2. First insert the appropriate Torx wrench(included) into the
crossbolt head, then rotate to loosen cross bolt then
aach the sight into a suitable position,
and finally tighten the clamp screw to 15 IN/LBS using
non-permanent thread locker. (Fig3)
Bri ghtness Decrease
Bri ghtness Increase
Protective Cap
Objective Lens
Eyepiece Lens
T10 Torx Crossbolt
Model
Fig 3
Clamp
screw head
Cross bolt
2) Baery installation(Fig2-2):
a) Insert the baery into the battery tray 2032 with
oriented with the POSITIVE SIDE DOWN.
b) Insert and press the tray into the battery compartment.
c)
Fasten screw 1,2.
Caution:
The loss or damage of seal ring will cause water to leak into
the compartment and may damage electronic circuits and
the device.
when battery runs out or for other condions that require
the baery to be changed :
1) Removing the battery (Fig 2-1):
a)Loosen screws 1,2.
b)Insert coin or similar object in the battery tray slot, pry
out the battery tray, and remove the discharged baery
by liing it up. A tool is provided for this purpose.
Fig 2-2
Slot
Screw 1
Screw 2
Screw 2
Screw 1
Battery
cabin
Battery
Seal ring
Sight operation
The operation panel is on the top of sight.(see Fig4)
Produkspesifikasjoner
| Merke: | Holosun |
| Kategori: | Ikke kategorisert |
| Modell: | Paralow HS403B |
Trenger du hjelp?
Hvis du trenger hjelp med Holosun Paralow HS403B still et spørsmål nedenfor, og andre brukere vil svare deg
Ikke kategorisert Holosun Manualer
3 April 2025
3 April 2025
3 April 2025
2 April 2025
2 April 2025
2 April 2025
25 Desember 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
Ikke kategorisert Manualer
- Hitachi
- Vivotek
- Bora
- Clarion
- Lionelo
- Savio
- Smeg
- LAS
- Magivaac
- Easymaxx
- BlaknBlu
- Princeton Tec
- Rega
- SKB
- Cayin
Nyeste Ikke kategorisert Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025