Jensen CMR8629 Bruksanvisning

Jensen Mottaker CMR8629

Les nedenfor 📖 manual på norsk for Jensen CMR8629 (22 sider) i kategorien Mottaker. Denne guiden var nyttig for 4 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/22

INSTALLATION/OWNER’S MANUAL

Multimedia Receiver with Bluetooth®

featuring a 6.8” digital touch screen TFT

CMR8629

The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.

microSD Logo is a trademark of SD-3C, LLC.

Other trademarks and trade names are those of their respective owners.

CMR8629 OPERATION

Safety Information

Please read all instructions carefully before attempting to install or operate.

Due to its technical nature, it is highly recommended that your Jensen CMR8629 is installed by a professional

installer or an authorized dealer. This product is only for use in vehicles with 12VDC negative ground only.

To prevent damage or injury:

• Make sure to ground the unit securely to the vehicle chassis ground.

• Do not remove the top or bottom covers of the unit.

• Do not install the unit in a spot exposed to direct sunlight or excessive heat or the possibility of water splashing.

• Do not subject the unit to excessive shock.

• When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may

cause the unit to malfunction.

• To prevent short circuits when replacing a fuse, disconnect the wiring harness first.

• Use only the provided hardware and wire harness.

• You cannot view video while the vehicle is moving. Find a safe place to park and engage the parking brake.

• If you experience problems during installation, consult your nearest Jensen dealer.

• If the unit malfunctions, reset the unit as described on page 10 first. If the problem still persists, consult your

nearest Jensen dealer or call tech assistance at 888-921-4088.

• To clean the monitor, wipe only with a dry silicone cloth or soft cloth. Do not use a stiff cloth, or volatile solvents

such as paint thinner and alcohol. They can scratch the surface of the panel and/or remove the printing.

• When the temperature of the unit falls (as in winter), the liquid crystal inside the screen will become darker than

usual. Normal brightness will return after using the monitor for a while.

• When extending the ignition, battery or ground cables, make sure to use automotive-grade cables or other cables

with an area of 0.75mm (AWG 18) or more to prevent voltage drops.

• Do not touch the liquid crystal fluid if the LCD is damaged or broken. The liquid crystal fluid may be hazardous

to your health or fatal. If the liquid crystal fluid from the LCD contacts your body or clothing, wash it off with soap

immediately.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Produkspesifikasjoner

Merke:	Jensen
Kategori:	Mottaker
Modell:	CMR8629

Trenger du hjelp?

Hvis du trenger hjelp med Jensen CMR8629 still et spørsmål nedenfor, og andre brukere vil svare deg

Ditt navn*

Din e-post*

Skriv spørsmålet ditt her

Mottaker Jensen Manualer

Jensen VX3012 Bruksanvisning

26 August 2025

Jensen VX7020N Bruksanvisning

26 August 2025

Jensen CAR68 Bruksanvisning

26 August 2025

Jensen CMR8629 Bruksanvisning

26 August 2025

Jensen JA2B Bruksanvisning

26 August 2025

Jensen MPQ914 Bruksanvisning

24 Januar 2025

Jensen MPR210RGB Bruksanvisning

7 Januar 2025

Jensen XDA95RB Bruksanvisning

11 Desember 2024

Jensen CAR710-4BC Bruksanvisning

26 Oktober 2024

Jensen CAR710-4 Bruksanvisning

15 Oktober 2024

Mottaker Manualer

Nyeste Mottaker Manualer

Infinity Reference 7005A Bruksanvisning

27 August 2025

Infinity Beta Digital 50 Bruksanvisning

27 August 2025

Infinity Reference 4555A Bruksanvisning

27 August 2025

Infinity Marine M6001A Bruksanvisning

27 August 2025

Infinity Reference RSA 120 Bruksanvisning

27 August 2025

Infinity Reference 551A Bruksanvisning

27 August 2025

Infinity Reference RSA 250 Bruksanvisning

27 August 2025

Infinity Kappa Perfect 3002A Bruksanvisning

27 August 2025

Infinity Kappa K2 Bruksanvisning

27 August 2025

Infinity Marine M3004A Bruksanvisning

27 August 2025