Leviton 49990-LDL Bruksanvisning
Leviton
Ikke kategorisert
49990-LDL
Les nedenfor π manual pΓ₯ norsk for Leviton 49990-LDL (11 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 30 personer og ble vurdert med 4.7 stjerner i gjennomsnitt av 15.5 brukere
Side 1/11
PK-A3141-10-02-5A
(REF-0R-49990-00 -06)-00
ξ
ξ,>?ξξ@=0ξξ4-0=ξ!;?4.ξξ:990.?:=
%ξξξ! ξξ&!$
ξξξξξξξ%&
ξξξξξξ%%&
ξξξξξξξ%ξ
ξξξξξξξ%ξ
ξξξξξξ%%ξξ
ξξξξξξξξξξ
ξξξξξξξξξ
ξξξξξξ%ξξ
ξξξξξξξξξ
ξξξξξξξξξ
ξξξξξξ%ξξ
%&
R
ξ! ξξ&!$
A Division of Leviton Manufacturing Co.,Inc.
Technical Support: 800-824-3005
Fax: (425) 483-5270
www.levitonvoicedata.com
Description Part No.
Multimode STβConnector 50/125 & 62.5/125 49990-MST
Singlemode STβConnector 49990-SST
Multimode SCβConnector 50/125 &β62.5/125 (beige) 49990-MSC
LO Multimode SC Connector (aqua) 49990-LSC
Singlemode SCβConnector (blue) 49990-SSC
SC Duplex Clip, black (Bag of 25) 49886-DSC
Mulimode LCβConnector with 3mm boot (beige) 49990-ML2
LO Multimode LCβConnector with 3mm boot (aqua) 49990-LL2
Singlemode LC Connector with 3mm boot (blue) 49990-SL2
Multimode LCβConnector with .9mm boot (beige) 49990-MDL
LO Multimode LCβConnector with .9 mm boot (aqua) 49990-LDL
Singlemode LCβConnector with .9mm boot (blue) 49990-SDL
LCβDuplex Clip, Multimode, beige (bag of 25) 49886-DLM
LCβDuplex Clip, Singlemode, blue (bag of 25) 49886-DLS
Fast Cure Tool Kit 49800-FTK
Fast Cure Consumables Kit 49800-FCC
Adhesive Primer Kit 49800-680
Crimp Tool with .128, .151, .178 hex die 49886-FCT
Replacement Needles (19 gauge, bags of 25) 49886-FCN
Syringes (bags of 25) 49886-SYR
LCβPolishing Puck 49886-LCP
LCβDuplex Scope Adapter 49886-LCD
LC Simplex Scope Adapter 49886-LCS
Fast Cure Carrying Case 49886-FCC
Part Numbers
ξξξξ! ξξ&!$
PK-A3141-10-02-5A
(REF-0R-49990-00- 06)00-
ξξ
%&ξ%ξξ)ξξξξξξ&ξξξξξξξξ
ξ
ξξξ
ξξξ)ξξξξξξ&ξξξξξξξξ
ξξξ
ξξξξξ'ξξξ$ξξξξξξξξ
ξξξ
ξ>>08-7Dξξ9>?=@.?4:9>ξ
ξξ
ξξ"$ξ"ξ$ξ
ξ77ξξ:990.?:=ξ&D;0>ξ
NOTE: If using 900 Β΅m buffered fiber, do not use the crimp tube in step 1.
1. Slide the boot and the crimp tube onto the fiber, with the small end inserted first. (Figure 1)
ξ:=ξξ88ξξ,.60?0/ξξ,-70ξξUse the ribbed boot, provided.
ξ:=ξξξξS8ξξ@110=0/ξξ,-70ξξUse the smooth boot, provided.
NOTE: If using an SC Connector on 900Β΅m buffered fiber, you must install the SC body into the housing
before continuing to step 2. Align the body with the connector housing, then insert the body into
the housing until it snaps into place. Use the dust cap to push the body into the housing.
2. Strip the jacket and/or buffer using the measurements provided in the chart below, and strip in
increments of 1/4β. If using jacketed cable, trim the aramid strands as indicated, below.
(Figure 2a-c)
!&ξξξ&:ξ307;ξ,A:4/ξ?::7ξξ-@110=ξ,9/ξ14-0=ξ.:9?,849,?4:9ξξ.70,9ξ5,.60?ξ,9/ξ0C;:>0/ξ-@110=ξB4?3
,ξξξξξ,7.:3:7ξB4;0ξξ?309ξB4?3ξ,ξ749?ξ1=00ξB4;0ξξ-:?3ξ-01:=0ξ,9/ξ,1?0=ξ>?=4;;492ξ
3. Clean exposed fiber with a 99% alcohol wipe followed by a lint-free wipe to remove any contaminants.
ξ !&ξξξξ8,20>ξ,=0ξ9:?ξ?:ξ>.,70ξ
%ξξξ:990.?:=ξ&D;0>ξ:9ξξ88ξξ,.60?0/ξξ,-70ξ! ξ+ξ
4. Insert spacer over buffer and push all the way down, until it rests against the jacket. (Figure 3)
ξ7409?ξ :?0>ξ :?0>ξ/0ξ7W@?474>,?0@=ξ :?,>ξ/07ξ@>@,=4:ξ
strip length 20 mm
1/4
1/4
3/4
1 3/4
1/2
1 1/2
apply primer 10mm
ξ
ξ !&ξξξξ8,20>ξ,=0ξ9:?ξ?:ξ>.,70ξ
PK-A3141-10-02-5A
(REF-0R-49990-00- 06)00-
ξ
ξ
ξξξξ%%ξξξξξ
ξ77ξξ:990.?:=ξ,9/ξξ4-0=ξ&D;0>ξ
1. Remove the dust cap from the connector.
2.
2.
2.
2.2.
Dry fit the fiber by inserting the fiber into the connector. This will assure that all coating has been
removed and the fiber can be inserted into the connector ferrule.
3. Shake the adhesive bottle before using. Remove the cap from the adhesive bottle, and attach the
needle by pressing it gently onto the top of the bottle until you feel it set into place.
NOTE: Syringes are also available for inserting adhesive.
4. Insert the needle and firmly hold it against the back of the connector while filling it. Being careful not to
overfill the connector, squeeze the bottle gently, injecting the adhesive into the connector. Continue
until a dot of adhesive is visible at the other end, then remove the needle. Wipe away excess adhesive
from the end of the ferrule.
5. Using the brush attached to the lid on the bottle of primer, apply the primer to the first 10mm of the
exposed fiber. See figure 2a.
6. Insert the fiber into the back of the connector. To prevent premature bonding, use continuous motion,
until the fiber is fully seated in the connector. The primer will activate adhesive and begin the bonding
process.
!&ξξξ&30ξ14-0=ξ>3:@7/ξ-0ξ49>0=?0/ξB4?349ξξξξ>0.:9/>ξ:1ξ;=48492ξ
7. Hold the fiber in place for 10-20 seconds, and allow up to 3 minutes for the adhesive to bond.
8. If using any cable type but jacketed fiber, slide the boot back up over the back of the connector, now. If
using jacketed fiber, follow the steps, below.
ξ//4?4:9,7ξ%?0;>ξξ:=ξξ88ξξ,.60?0/ξξ,-70ξ! ξ+ξ
9. Arrange the aramid strands evenly around the end of the connector, then slide the crimp tube over the
aramid strands and connector. Using a crimp tool, crimp the tube at both the large end (step 1) and the
small end (step 2). (Figure 4)
%&ξ%ξξξξ7,=20ξ09/ξξUse the .178β hex die.
%&ξ%ξξξξ>8,77ξ09/ξξUse the .151β hex die.
ξξξξUse the .128β hex die.
ξ
ξ7409?ξ :?0>ξ :?0>ξ/0ξ7W@?474>,?0@=ξ :?,>ξ/07ξ@>@,=4:ξ
ξξ
Produkspesifikasjoner
| Merke: | Leviton |
| Kategori: | Ikke kategorisert |
| Modell: | 49990-LDL |
Trenger du hjelp?
Hvis du trenger hjelp med Leviton 49990-LDL still et spΓΈrsmΓ₯l nedenfor, og andre brukere vil svare deg
Ikke kategorisert Leviton Manualer
25 Februar 2025
29 Desember 2024
16 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
Ikke kategorisert Manualer
- Kospel
- Tiptop Audio
- Xinfrared
- IDIS
- Cambridge
- Weston
- Sole Fitness
- CRUX
- ELTA Music
- PTZ Optics
- American DJ
- Ulsonix
- Crimson
- Pardini
- MyPOS
Nyeste Ikke kategorisert Manualer
8 Oktober 2025
8 Oktober 2025
8 Oktober 2025
8 Oktober 2025
8 Oktober 2025
8 Oktober 2025
8 Oktober 2025
8 Oktober 2025
8 Oktober 2025
8 Oktober 2025