Lutron FCJS-010 Bruksanvisning

Lutron Smart hjem FCJS-010

Les nedenfor 📖 manual på norsk for Lutron FCJS-010 (8 sider) i kategorien Smart hjem. Denne guiden var nyttig for 31 personer og ble vurdert med 5.0 stjerner i gjennomsnitt av 16 brukere

Last ned PDF

Side 1/8

Radio Powr Savr

Occupancy

Sensor

Pico

Remote

Control

PowPak

Dimming

Module

30 ft

(9 m) max

40 ft (12 m)

30 ft (9 m)

PowPak

Dimming Module

Install in center of room to

maximize RF coverage.

Connect mains wiring (switched hot, neutral) to each ﬁxture.

Connect 0 –10 V- control (+ and – ) to each ﬁxture.

–

NEU

HOT

Class 2

MAINS

Fixture Earth

Green/Yellow

To additional 0 –10 V- ﬁxtures

Neutral

Switched Line/Hot

Violet

Pink*

–

WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit

breaker before installing the unit.

Sample

ballast shown

Start Here

Mount, Wire, and Install 0 –10 V- Devices

and Lighting Fixtures

Consult third-party device installation guide

PowPak Dimming Module with 0 –10 V- can be installed on a junction box or marshalling box using the conduit nut (provided) or with mounting

screws (not provided). The device must NOT be mounted inside a ﬁxture or other metallic enclosure – only on the exterior of a ﬁxture. Please

consult local and national electric codes for proper installation.

If installing unit inside a junction box, please see Application Note #423 (P/N 048423 at www.lutron.com).

Once installed, energize the PowPak Dimming Module with 0 –10 V-.

Use the Toggle button “ u” to toggle between high-end and OFF to verify ballast wiring.

Use the Raise “

▲

” and Lower “

” buttons to verify control wiring.

Install PowPak Dimming Module with 0 –10 V-

Suggested Installation Location: Center of room to ensure proper RF coverage of area.

Switched Line/Hot (Red)

–

Line/Hot

(Black)

To Fixtures

0 –10 V- to Fixtures*

Neutral (White)

Neutral

Junction Box

1/2 in (21 mm) Knockout Opening

Conduit Nut

RMJS-8T-DV-B / URMJS-8T-DV-B

Switched Line/Hot (Red)

–

Line/Hot

(Black)

To Fixtures

0 –10 V-

to Fixtures *

Neutral (White)

Neutral

Junction Box

1/2 in (21 mm) Knockout Opening

Conduit Nut

RMJS-8TN-DV-B

Switched Line / Hot (Red)

–

Line / Hot (Black)

To Emergency

Fixtures

0 –10 V- to

Emergency

Fixtures*

Neutral (White)

Neutral

Junction Box

1/2 in (21 mm)

Knockout Opening

Conduit Nut

Emergency

Backup

Generator

Automatic

Transfer

Switch

Regular

Utility Power

Neutral

120 / 277 V~ Normal Feed

Neutral

120 / 277 V~ Emergency Feed

Note: For periodic testing and maintanance of emergency systems, use the toggle button of

the RMJS-8T-DV-B-EM to ensure proper operation. Make sure PowPak buttons remain

accessible.

Note: Momentary power outages can envoke emergency mode on the dimming module. See

Troubleshooting section for details.

RMJS-8T-DV-B-EM

* Use 18 AWG to 16 AWG (0.75mm

to 1.5mm

) solid wire only

vive.lutron.com

Programming with a Vive Hub

Use an iOS® or Android®

compatible device.

Open the app and follow

the instructions.

Note: For further information on set up,

programming, and troubleshooting with a

Vive system, please refer to the installation

instructions included with the Vive hub or

visit www.lutron.com/vive

Note: For programming the PowPak

Dimming Module without a Vive hub see

reverse side.

Vive

Download the Lutron

Vive app.

041588

Rev. A

09/2020

PowPak | Installation

Dimming Module with 0 –10 V-

English

All Wireless

Transmitters must

be installed within 30 ft

(9 m) of the PowPak Dimming

Module with 0 –10 V-.

0 –10 V- Control: 10 V- 60 mA

UL 2043 Plenum Rated

UL 924 Listed (RMJS-8T-DV-B-EM)

Compatible with ANSI E1.3 2001 (R2006), IEC 60929 Annex E

120 / 277 V~ 50 / 60 Hz 8 A

RMJS-8T-DV-B

URMJS-8T-DV-B

RMJS-8TN-DV-B

Important Notes: Please read before installing.

For installation by a qualiﬁed electrician in accordance with all local and

national electrical codes (including periodic testing and maintenance of

emergency systems).

• Note: Use copper conductors only.

• Check to see that the device type and rating is suitable for the application.

• DO NOT install if product has any visible damage.

• If moisture or condensation is evident, allow the product to dry completely

before installation.

• Operate between 32 °F and 104 °F (0 °C and 40 °C) ambient.

• 0% to 90% humidity, non-condensing.

• For indoor use only.

Note for Replacement:

RMxS and URMxS - the "S" model can replace the non-"S" model

041771

Rev. A

09/2020

Part of the Vive Family

120 / 277 V~ 50 / 60 Hz 8 A

RMJS-8T-DV-B-EM

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be

followed including the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS.

• Do not use outdoors.

• Do not mount near gas or electric heaters.

• Equipment should be mounted in locations and at heights where it will not be

subjected to tampering by unauthorized personnel.

• The use of accessory equipment not recommended by the manufacturer may

cause an unsafe condition.

• Do not use this equipment for other than its intended use.

SAVE THESE INSTRUCTIONS

Test

Link

Cal.

For each system, ensure that you have:

One PowPak Dimming Module At least one Wireless Transmitter At least one 0 –10 V- Fluorescent Ballast or LED Driver

Required Components

Radio Powr Savr Occupancy / Vacancy Sensor

(10 maximum)

Radio Powr Savr Daylight Sensor

(1 maximum)

Pico Remote Control

(10 maximum)

60 mA maximum for the control lines. Switches up to 8 A total.

May be pre-installed in light ﬁxture.

Note: All drivers and ballasts used with Vive wireless controls must comply with the

limits for a Class A device, pursuant to Part 15 of the FCC rules.

PowPak Dimming Module with 0 –10 V-

(1 maximum)

Raise

Toggle

Lower

Load Status LED

Consult third-party 0 –10 V- ﬁxtures installation guide for ﬁxture-speciﬁc wiring.

For mounting and wiring best practices see Lutron Application Note #620 (P/N 048620).

Customer Assistance www.lutron.com/support

Wireless Controls: All lights

Default Functionality

Daylight Sensor

All lights dim in response to daylight.

On: 100% ; Favorite: 50%; Off: 0%

Occupancy Sensors

Occupied: All lights100% ; Unoccupied: All lights off

Lutron Electronics Co., Inc. | 7200 Suter Road

Coopersburg, PA 18036-1299, U.S.A.

* This wire may be gray on older products or in retroﬁt applications.

Produkspesifikasjoner

Merke:	Lutron
Kategori:	Smart hjem
Modell:	FCJS-010
Bruksanvisning:	Ja
Tilkoblingsteknologi:	Trådløs
Antall per pakke:	1 stykker
AC-inngangsspenning:	120 - 277 V
Produktfarge:	Green, White
Pakkedybde:	32 mm
Pakkehøyde:	87 mm
Pakkebredde:	48 mm
Arbeidsfrekvens:	431 - 437 MHz
Overføringsavstand:	9 m