Maxsa 43319-X Bruksanvisning
Maxsa
Ikke kategorisert
43319-X
Les nedenfor 📖 manual på norsk for Maxsa 43319-X (3 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 17 personer og ble vurdert med 4.6 stjerner i gjennomsnitt av 9 brukere
Side 1/3
ASSEMBLY AND INSTRUCTION GUIDE
ABOUT YOUR LED OUTDOOR WALL SCONCE
The
LED Outdoor Wall Sconce
is perfect for porches,
doorways, or around the house.
The
LED Outdoor Wall Sconce
has a built-in motion sensor,
which automatically turns on the light when movement of a
heat source (such as people, animals, or cars) is detected in
the area. The light remains on while motion continues to be
detected in the area.
The
LED Outdoor Wall Sconce
also has a built-in photosensor
so that the light only turns on at night.
The
LED Outdoor Wall Sconce
may function irregularly or not
at all at temperatures below ˚ F / ˚ C. 0 -17.8
Normal operation will return when the temperature rises.
The
LED Outdoor Wall Sconce
requires 4 C cell batteries (not
included). The batteries typically last up to 1 year under
normal use.
The 5 super bright LEDs in the
LED Outdoor Wall Sconce
have an estimated life of 30,000 hours so they should never
need changing.
BATTERY INSTALLATION
1. The
LED Outdoor Wall Sconce
requires 4 C cell batteries
(not included).
2. To access the battery compartment, remove the 2 thumb
screws from the top cover. Remove the top cover.
BATTERY INSTALLATION (CONTINUED)
3. Remove the battery compartment cover by squeezing
the two tabs on the cover inward and pulling up.
4. Install the 4 C cell batteries in the proper +/- polarity
orientation as shown in the illustration above. The
positive ends of the batteries should face the low battery
contacts and the negative ends of the batteries should
face the elevated spring terminals in the battery
compartment. If your unit includes a clear rubber spacer
between the two halves of the battery compartment,
please reinsert it between the two halves.
5. Reinstall the battery compartment cover by aligning the
tabs and pressing the battery compartment cover down
until the battery compartment cover clicks into place.
6. Reassemble the
LED Outdoor Wall Sconce
by replacing
the top cover and re-installing the two thumb screws.
Tighten the thumb screws by hand as tightly as possible
to ensure a waterproof seal.
Model # 4 9
page 1
LED Outdoor Wall Sconce
BATTERY-POWERED MOTION-ACTIVATED
Thumb Screw
Battery Compartment Cover
4 C Batteries
Squeeze tabs inward
Insert 4 C batteries
in the proper +/
-
orientation
Produkspesifikasjoner
| Merke: | Maxsa |
| Kategori: | Ikke kategorisert |
| Modell: | 43319-X |
Trenger du hjelp?
Hvis du trenger hjelp med Maxsa 43319-X still et spørsmål nedenfor, og andre brukere vil svare deg
Ikke kategorisert Maxsa Manualer
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
Ikke kategorisert Manualer
- Stelton
- Gemini
- Simmons
- Rocketfish
- REVITIVE
- Indiana Line
- Shokz
- Xuma
- Umidigi
- Steiner
- Gustavsberg
- Videotec
- CubuSynth
- Olimpia Splendid
- Frilec
Nyeste Ikke kategorisert Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025