Metabo C8FSHE Bruksanvisning
Les nedenfor 📖 manual på norsk for Metabo C8FSHE (3 sider) i kategorien Bli verre. Denne guiden var nyttig for 20 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/3
Model
Modèle
Modelo
C 8FSHE
C 8FSHE(S)
C 8FSE
C 8FSE(S)
Slide Compound Miter Saw
Scie à onglets coulissante
Ingletadora telescopica
(Laser Marker and Light Equipment)
(Marqueur laser et lumière)
(Equipo con marcador láser y luz)
DOUBLE INSULATION
DOUBLE ISOLATION
AISLAMIENTO DOBLE
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand this
manual BEFORE operating the power tool. Please keep this manual available for other users and owners
before they use the power tool. This manual should be stored in safe place.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort ou de
sérieuses blessures corporelles !
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. Prière
de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce mode d’emploi
à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode
d’emploi doit être conservé dans un endroit sûr.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar en lesiones
de gravedad o la muerte!
Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda este
manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan leerlo otras
personas antes de utilizar la herramienta eléctrica. Este manual debe ser guardado en un lugar seguro.
0000BookC8FSHEUS.indb10000BookC8FSHEUS.indb1 2018/11/2816:50:322018/11/2816:50:32
2
English
IMPORTANT SAFETY INFORMATION
Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining
this power tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An
accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which contain the operation and
maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identifi ed by WARNINGS on the power tool and in this Instruction
Manual.
NEVER use this power tool in a manner that has not been specifi cally recommended by metabo HPT.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or may cause machine
damage.
NOTE emphasizes essential information.
MEANINGS OF SYMBOLS
Symbols
WARNING
The following show symbols used for the machine. Be sure that you understand their meaning before use.
To reduce the risk of injury, user must read instruction
manual.
Vvolts
Hz hertz
Always wear eye protection.
Aamperes
no
no load speed
Always wear hearing protection.
Class II Construction
---/min revolutions per minute
CAUTION
Do not stare at operating lamp.
alternating current
SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WARNING:
Read all safety warnings, instructions, illustrations and specifi cations provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of fl ammable liquids, gases or
dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a
power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools.
Unmodifi ed plugs and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving
parts.
Damaged or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply.
Use of an RCD reduces the risk of electric shock.
0000BookC8FSHEUS.indb20000BookC8FSHEUS.indb2 2018/11/2816:50:332018/11/2816:50:33
3
English
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool.
Do not use a power tool while you are tired or under the
infl uence of drugs, alcohol or medication.
A moment of inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection.
Protective equipment such as a dust mask, non-skid safety
shoes, hard hat or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off -position before connecting to power source and/
or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench before turning the
power tool on.
A wrench or a key left attached to a rotating part of the power
tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at
all times.
This enables better control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair and clothing away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving
parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used.
Use of dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool safety
principles.
A careless action can cause severe injury within a fraction of
a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool
for your application.
The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it
on and off .
Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from the
power tool before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may aff ect the
power toolʼs operation. If damaged, have the power tool
repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations diff erent from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free
from oil and grease.
Slippery handles and grasping surfaces do not allow for safe
handling and control of the tool in unexpected situations.
5) Service
a) Have your power tool serviced by a qualifi ed repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of children
and infi rm persons.
SAFETY INSTRUCTIONS FOR MITER SAWS
a) Miter saws are intended to cut wood or wood-like products,
they cannot be used with abrasive cut-off wheels for cutting
ferrous material such as bars, rods, studs, etc.
Abrasive dust causes moving parts such as the lower guard to
jam. Sparks from abrasive cutting will burn the lower guard, the
kerf insert and other plastic parts.
b) Use clamps to support the workpiece whenever possible. If
supporting the workpiece by hand, you must always keep
your hand at least 100 mm from either side of the saw blade.
Do not use this saw to cut pieces that are too small to be
securely clamped or held by hand.
If your hand is placed too close to the saw blade, there is an
increased risk of injury from blade contact.
c) The workpiece must be stationary and clamped or held
against both the fence and the table. Do not feed the
workpiece into the blade or cut "freehand" in any way.
Unrestrained or moving workpieces could be thrown at high
speeds, causing injury.
d) Push the saw through the workpiece. Do not pull the saw
through the workpiece. To make a cut, raise the saw head
and pull it out over the workpiece without cutting, start the
motor, press the saw head down and push the saw through
the workpiece.
Cutting on the pull stroke is likely to cause the saw blade to climb
on top of the workpiece and violently throw the blade assembly
towards the operator.
e) Never cross your hand over the intended line of cutting either
in front or behind the saw blade.
Supporting the workpiece “cross handed” i.e. holding the
workpiece to the right of the saw blade with your left hand or vice
versa is very dangerous.
f) Do not reach behind the fence with either hand closer than
100 mm from either side of the saw blade, to remove wood
scraps, or for any other reason while the blade is spinning.
The proximity of the spinning saw blade to your hand may not be
obvious and you may be seriously injured.
g) Inspect your workpiece before cutting. If the workpiece
is bowed or warped, clamp it with the outside bowed face
toward the fence. Always make certain that there is no gap
between the workpiece, fence and table along the line of the
cut.
Bent or warped workpieces can twist or shift and may cause
binding on tile spinning saw blade while cutting. There should be
no nails or foreign objects in the workpiece.
h) Do not use the saw until the table is clear of all tools, wood
scraps, etc., except for the workpiece.
Small debris or loose pieces of wood or other objects that contact
the revolving blade can be thrown with high speed.
0000BookC8FSHEUS.indb30000BookC8FSHEUS.indb3 2018/11/2816:50:332018/11/2816:50:33
Produkspesifikasjoner
| Merke: | Metabo |
| Kategori: | Bli verre |
| Modell: | C8FSHE |
Trenger du hjelp?
Hvis du trenger hjelp med Metabo C8FSHE still et spørsmål nedenfor, og andre brukere vil svare deg
Bli verre Metabo Manualer
19 Januar 2025
31 Desember 2025
27 Oktober 2024
Bli verre Manualer
- Bli verre MSW
- Bli verre Royal Catering
- Bli verre Bosch
- Bli verre DeWalt
- Bli verre Gamma
- Bli verre Rikon
- Bli verre Stihl
- Bli verre Topex
- Bli verre Husqvarna
- Bli verre Gude
- Bli verre Ryobi
- Bli verre Hitachi
- Bli verre Milwaukee
- Bli verre Makita
- Bli verre Einhell
- Bli verre Anova
- Bli verre Spear & Jackson
- Bli verre Fuxtec
- Bli verre Vonroc
- Bli verre Worx
- Bli verre Stanley
- Bli verre Black And Decker
- Bli verre Powerplus
- Bli verre Ozito
- Bli verre Craftsman
- Bli verre Maruyama
- Bli verre Hilti
- Bli verre Solo
- Bli verre Silverline
- Bli verre Evolution
- Bli verre Triton
- Bli verre Al-ko
- Bli verre Stalco
- Bli verre Fieldmann
- Bli verre Prime3
- Bli verre Yellow Garden Line
- Bli verre Parkside
- Bli verre Extralink
- Bli verre Ergotools Pattfield
- Bli verre CMI
- Bli verre Goon
- Bli verre Proviel
- Bli verre Bavaria
- Bli verre Sun Joe
- Bli verre Black Decker
- Bli verre Baumr-AG
- Bli verre EGO
- Bli verre Powerblade
- Bli verre Sovereign
- Bli verre King Craft
- Bli verre Total
- Bli verre Turbo-Silent
- Bli verre Global
- Bli verre Herkules
- Bli verre Alpina
- Bli verre Shindaiwa
- Bli verre Bavaria By Einhell
- Bli verre Prowork
- Bli verre Backyard Pro
- Bli verre Alpha Tools
- Bli verre Pro-Cut
- Bli verre Stiga
- Bli verre Trotec
- Bli verre Echo
- Bli verre Maxbear
- Bli verre TAURUS Titanium
- Bli verre Duro Pro
- Bli verre Bestgreen
- Bli verre Ribimex
- Bli verre MacAllister
- Bli verre McKenzie
- Bli verre Max Bahr
- Bli verre Rona
- Bli verre Grizzly
- Bli verre Troy-Bilt
- Bli verre Kraftronic
Nyeste Bli verre Manualer
3 April 2025
3 April 2025
2 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
30 Mars 2025
30 Mars 2025