PAC AP4-TY14 Bruksanvisning
Les nedenfor 📖 manual på norsk for PAC AP4-TY14 (5 sider) i kategorien Mottaker. Denne guiden var nyttig for 41 personer og ble vurdert med 4.7 stjerner i gjennomsnitt av 21 brukere
Side 1/5
© 2024 Stinger Solutions
C
Page 1
Rev: 1
Date:09242024
Advanced Amplier Interface
for Select Toyota Applications
AP4-TY14
The AP4-TY14 provides a 6-channel pre-amp output for use with aftermarket audio equipment. Using the full range
xed level head unit output, in conjunction with data bus messages, the AP4-TY14 delivers a variable 5v RMS pre-
amp output with fading, balance, equalization, and level control capabilities. The module also retains audio from
other vehicle features such as factory navigation prompts, Bluetooth and Voice Activation. An accessory controlled
remote amplier turn on wire is also provided by the AP4-TY14. When used in conjunction with the APA-TOS1 (sold
separately), the module can provide a variable 2-channel ber optic digital audio output (TOSLINK).
Introduction and Features
Important Notes
1. Toyota Safety Connect (SOS) can easily be retained. See the page 3 for detailed instructions.
2. The aftermarket amplier must have a very solid ground and the amplier power/ground connections should be made
before connecting the RCA's or Remote on the AP4-TY14.
3. The factory radio's speed controlled volume, DSP, and surround sound mode are not supported by the AP4 outputs.
4. The factory amplier must remain connected and in the vehicle after the AmpPRO has been installed.
5. Prior to testing, cycle the ignition off and back on again to properly initialize the AP4-TY14.
6. The radio's beep setting must be enabled on the factory radio in order to hear the audible tones when making selections
through the radio.
7. Initially, if the beep through the AP4-TY14 does not match the on/off selection through the radio, cycle the beep to the
opposite setting and back, then test again.
8. The radio's beep volume and minimum volume levels are set to 0 dB by default. If you are happy with this level in your
particular application, additional adjustment is not required. Please refer to the Setup and Conguration section on page 4
for more details.
9. The Radio's Nav / VR Voice, incoming E-mail tone, Ringtone, In-Call, Incoming SMS / MMS tone and Incoming SMS Voice
volumes can be adjusted through the radio's settings menu as they were prior to installation of the AP4-TY14.
10. The remote output is rated at 2A of current. If more current is needed, an external relay must be used.
11. Channels 5 and 6 are non-fading outputs. The output level of channels 5 and 6 can be controlled using the supplied level
control knob.
Wiring Connection Chart
To Aftermarket
Amplier
Non-FadingRearFront
1(L) 2(R) 4(R) 5(L) 6(R)3(L)
Non-Fading
Level Control
Knob
Remote Turn On Output (2A Max)
SOS Mute ( - Trigger Input )
GRAY
GRAY
BLACK
BLACK
WHITE
WHITE
28-pin
10-pin
30-pin
Produkspesifikasjoner
| Merke: | PAC |
| Kategori: | Mottaker |
| Modell: | AP4-TY14 |
Trenger du hjelp?
Hvis du trenger hjelp med PAC AP4-TY14 still et spørsmål nedenfor, og andre brukere vil svare deg
Mottaker PAC Manualer
3 August 2025
12 Februar 2025
12 Februar 2025
Mottaker Manualer
- Ferguson
- Atoll
- Lab Gruppen
- Black Lion Audio
- SmartSystem
- BZBGear
- Irradio
- Klipsch
- Technical Pro
- Dynacord
- Mooer
- Palmer
- IFi Audio
- DARTS
- Ashly
Nyeste Mottaker Manualer
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025