Radson Turbo Bruksanvisning
Les nedenfor 📖 manual på norsk for Radson Turbo (6 sider) i kategorien Termostat. Denne guiden var nyttig for 30 personer og ble vurdert med 4.8 stjerner i gjennomsnitt av 15.5 brukere
Side 1/6
1
STARTING THE DEVICE:
Press the button 5 on the side of the Turbo to turn the
device on (Turbo + towel dryer).
• Indicators 2 and 3: Steady green - Turbo + Towel dryer
turned on
• Filter indicator 1: Off
• Indicator 3: Steady red - towel dryer running
BLOWER 2 OPERATING LIGHT:
• Off: Power Off
• Steady green: Power On
• Blinking red: Operating
TURBO 1000 WATT
The Turbo is designed to quickly raise the temperature in your bathroom.
• Install the timer in the same room as the towel dryer. The
timer must be installed about 1.5 metres above the floor,
on an inside wall, away from splashing water, direct
sunlight and direct source of direct thermal disturbance.
Note: To ensure proper infrared transmission:
- Do not obstruct transmitter and receiver cells
(bath towels in front of the cell).
- Avoid using electronic ballast lighting in the same room.
• Set the dial for the desired time and press the “OK / Boost”
button to start the blower.
NOTE: Forced operation of the device can be interrupted at
any time by pressing the “OK / Boost” button again. When
restarting the blower in this case, the remaining Boost time
will be the setting shown on the dial.
Infrared receiver on Turbo
UK
1. Filter cleaning indicator
2. Blower operation indicator
3. Towel dryer operation indicator
4. Infrared receiver cell
5. Start/towel dry button
SPECIFIC CASES
Overheating
If towels or any other obstructions block the Turbo outlet
excessively, causing overheating, the device will shut down
(indicators 2 and 3 blinking red / green). The Turbo operation
will restart once the temperature cools, for the remaining
preset length of time.
Thermal safety:
If the Turbo resistor overheats a manually reset thermal
safety device mechanically stops blower operation.
Indicator light status:
• Filter indicator 1: Blinking red and
• Blower indicator 2: Steady green
Important: A dirty filter can cause overheating. Clean it if
necessary. Press button 5 “start/stop” for 5 seconds to stop
this alarm.
Note: Please clean the filter each time the Clean Filter alarm
is triggered (“see Cleaning the Filter”).
Caution: if the cause of overheating has not been identified
the alarm will be triggered again. In this case, please contact
the installer since this may cause the Turbo to deteriorate
over time.
The infrared timer trans-
mitter lets you send a start
command to the Turbo for
a variable period of 0 to 2
hours.
TIMER ON HOT WATER VERSION DEVICES
21 43 5
Produkspesifikasjoner
| Merke: | Radson |
| Kategori: | Termostat |
| Modell: | Turbo |
Trenger du hjelp?
Hvis du trenger hjelp med Radson Turbo still et spørsmål nedenfor, og andre brukere vil svare deg
Termostat Radson Manualer
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
Radson 51052 - SLAVE RF 4 or 6 Zones Thermostaat Bruksanvisning
18 Oktober 2024
18 Oktober 2024
Termostat Manualer
- Bticino
- ACV
- AVM
- Bulex
- Tado
- Sygonix
- Hager
- VDH
- Muller
- Levica
- Econo-Heat
- Netatmo
- Eliwell
- Brink
- GENERAL Life
Nyeste Termostat Manualer
19 Oktober 2025
19 Oktober 2025
9 Oktober 2025
8 Oktober 2025
6 Oktober 2025
6 Oktober 2025
6 Oktober 2025
24 September 2025
24 September 2025
24 September 2025