Remington Virtually Indestructible PF7855AU Bruksanvisning

Remington Barbermaskin Virtually Indestructible PF7855AU

Les nedenfor 📖 manual på norsk for Remington Virtually Indestructible PF7855AU (2 sider) i kategorien Barbermaskin. Denne guiden var nyttig for 7 personer og ble vurdert med 4.9 stjerner i gjennomsnitt av 4 brukere

Last ned PDF

Side 1/2

8 9

For optimal shaver performance, clean your shaver after each use.

CAUTION!

• Do not remove or replace head assembly while shaver is running as it

may cause damage to the unit’s foils and cutters.

• To clean the external surfaces of the shaver, use a damp cloth. Do not

use strong detergents or other chemicals.

• To dry, wipe the surface of the shaver with a dry towel. Do not use a

hair dryer or heater to dry the shaver.

• The shaver should not be used until it has dried.

• Lubricate each cutter with household oil.

• This product contains no user serviceable parts.

Daily Cleaning:

1. Pull off Stubble comb/Head guard, if using, and rinse attachment.

2. Grasp the front and back of the cutter assembly and pull away from

the shaver body. (Diagram I)

3. Tap the stubble from the foils and cutters.

4. Use the cleaning brush to sweep any loose hairs from the cutters,

hairpocket, and trimmer. Pay close attention to

cleaning out the corners and crevices inside the

hairpocket. (Diagrams J–K)

5. Rinse head under running water.

6. Gently dry with towel or leave disassembled to air dry.

7. Replace hair pocket assembly when dry. (Diagram L)

8. Reattach the Stubble comb/Head guard to protect the

shaving head until next use.

Monthly Cleaning:

1. Perform the daily cleaning steps 1-4.

2. Place a drop of liquid soap on each cutter and in the

hairpocket. (Diagram M)

3. Brush the soap around vigorously with the supplied

cleaning brush. Be sure to work the soap into the

11 1210

VIRTUALLY INDESTRUCTIBLE

F O I L S H AV E R

5 YEAR WARRANTY

PF7855AU

To register your product go to

www.remington-products.com.au

www.remington.co.nz

USE & CARE

MANUAL

PLEASE READ

PRIOR TO USE

Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Limited

5 YEAR WARRANTY AGAINST DEFECTS

In this warranty:

Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the

Competition and Consumer Act 2010;

CGA means the New Zealand Consumer Guarantees Act 1993;

Goods means the product or equipment which was accompanied by this warranty and

purchased in Australia or New Zealand, as the case may be;

Manufacturer, We or us means:

1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd

ACN, 007 070 573; or

2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited,

as the case may be, contact details as set out at the end of this warranty;

Supplier means the authorised distributor or retailer of the Goods that sold you the Goods

in Australia or in New Zealand; and

You means you, the original end-user purchaser of the Goods.

1. Our goods come with guarantees that cannot be excluded under the Australian

Consumer Law, or the CGA. You are entitled to a replacement or refund for a major

failure and compensation for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to

be of acceptable quality and the failure does not amount to a major failure.

2. The benefits provided by this Warranty are in addition to all other rights and

remedies in respect of the Goods which the consumer has under either the

Australian Consumer Law or the CGA. The original purchaser of the Goods is

provided with the following Warranty subject to the Warranty Conditions:

3. We warrant the Goods for all parts defective in workmanship or materials

for the 5 year period (Warranty Period). If the Goods prove defective within

the Warranty Period by reason of improper workmanship or material, we

may, at our own discretion, repair or replace the Goods without charge.

**Blades, heads and cutters are not included in the lifetime warranty.

Warranty Conditions

4. The Goods must be used in accordance with the manufacturer’s instructions. This

Warranty does not apply should the defect in or failure of the Goods be attributable

to misuse, abuse, accident or non-observance of manufacturer’s instructions on the

part of the user. As far as the law permits, the manufacturer does not accept liability

for any direct or consequential loss, damage or other expense caused by or arising out

of any failure to use the Goods in accordance with the manufacturer’s instructions.

5. Consumable parts (such as shaver heads, cutters and foils) of the Goods are included

under this Warranty only where there is a defect in workmanship or materials used.

6. The warranty granted under clause 3 is limited to repair or replacement only.

7. Any parts of the Goods replaced during repairs or any product replaced remain the

property of the manufacturer. In the event of the Goods being replaced during the

Warranty Period, the warranty on the replacement Goods will expire on the same

date as for the Warranty Period on the original Goods which are replaced.

8. In order to claim under the warranty granted under clause 3 you must:

(a) Retain this warranty with your receipt/proof of purchase; and

(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid freight

within the Warranty Period accompanied with (i) the legible and unmodified original proof

of purchase, which clearly indicates the name and address of the Supplier, the date and

place of purchase, the product name or other product serial number and (ii) this warranty.

9. This warranty is immediately void if:

(a) Any serial number or appliance plate is removed or defaced;

(b) The Goods have been serviced or otherwise repaired by a person not

authorised to do so by us or where non approved replaced parts are used.

10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to

any industrial or commercial use of the Goods. The Goods must be connected to the

electrical voltage requirements as specified in the ratings label located on the Goods.

11. This warranty does not cover the cost of claiming under the warranty

or transport of the Goods to and from the Supplier or us.

12. This warranty is only valid and enforceable in Australia against Spectrum Brands

Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Limited.

Spectrum Brands Australia Pty Ltd

Locked Bag 3004

Braeside, VIC 3195

AUSTRALIA

Customer service in Australia: 1800 623 118

E-mail: consumer.enquiry@remington-products.com.au

Website: www.remington-products.com.au

Spectrum Brands New Zealand Limited

PO Box 9817

Newmarket, Auckland 1149

NEW ZEALAND

Customer service in New Zealand: 0800 736 776

E-mail: info@remington.co.nz

Website: www.remington.co.nz

REMINGTON SERVICE HOTLINE

Australia 1800 623 118 (toll free)

New Zealand 0800 736 776 (toll free)

AUTHORISED REPAIR CENTRES

Visit www.remington-products.com.au for Authorised repair centre details.

® Registered Trade Mark of Spectrum Brands Inc., (SBI) or one of its subsidiaries

Type: F20A

Rev. 01/22

Part No. T22-7002639

Suitable for use in bath and shower

This product conforms to radio frequency interference requirements

Any product purchased and used commercially carries a limited 90 Day Warranty.

corners of the hairpocket and into any especially dirty

cutters. (Diagram N)

4. Add a small amount of water to the cutters.

5. Replace the foil assembly. (Diagram O)

6. Turn on the shaver for approximately 30 seconds.

7. While the shaver is running, rinse the foils under

running water. (Diagram P)

8. Turn off shaver.

9. Remove foil assembly.

10. Rinse the cutters, hairpocket, and foil assembly

thoroughly. (Diagram Q)

11. Shake off excess water.

12. Replace foil assembly. (Diagram O)

13. Allow shaver to dry before next use and attach the

Stubble comb/ Head guard.

BATTERY DISPOSAL

Note: The battery is not intended to be removed or replaced

under normal use. The only time the battery should be

removed or the unit opened or disassembled, is at the end

of the product’s useful life before it is discarded.

• The PF7855AU shaver contains a nickel metal hydride battery. Once

the trimmer has reached the end of its life, to ensure proper disposal

of the product, please take the appliance to a recycling centre, where

the internal rechargeable battery should be removed by a professional

and recycled separately.

• For more information about recycling of electrical and battery operated

appliances, please contact your local council office or your household

waste disposal service.

Caution: Do not put in the fire or mutilate your batteries when disposing as

they may burst and release toxic materials. Do not short circuit as it may

cause burns.

DISPOSAL/RECYCLING

Legislation in some localities mandates that e-waste (anything with a plug,

battery or cord) is disposed of through controlled recycling facilities and

must not be disposed of in general household waste. For more information

about recycling of electrical and battery operated appliances, please

contact your local council or your local household waste disposal service.

Monthly Cleaning:

1. Perform the daily

cleaning steps 1-4.

2. Place a drop of

liquid soap on

each cutter and

in the hairpocket.

(Diagram M)

3. Brush the soap

around vigorously

with the supplied

cleaning brush.

Be sure to work

the soap into the

corners of the

hairpocket and into

any especially dirty

cutters.

(Diagram N)

4. Add a small amount

of water to the

cutters.

5. Replace the foil

assembly.

(Diagram O)

6. Turn on the shaver

for approximately

30 seconds.

7. While the shaver is running, rinse

the foils under running water.

(Diagram P)

8. Turn off shaver.

9. Remove foil assembly.

10.Rinse the cutters, hairpocket,

and foil assembly thoroughly.

(Diagram Q)

11. Shake off excess water.

12. Replace foil assembly. (Diagram O)

13. Allow shaver to dry before next

use and attach the Stubble comb/

Head guard.

• Do not remove or replace head

assembly while shaver is running

as it may cause damage to the

unit’s foils and cutters.

• To clean the external surfaces of

the shaver, use a damp cloth. Do

not use strong detergents or other

chemicals.

• To dry, wipe the surface of the

shaver with a dry towel. Do not use

a hair dryer or heater to dry the

shaver.

• The shaver should not be used until

it has dried.

• Lubricate each cutter with

household oil.

• This product contains no user

serviceable parts.

The shaver is a

wet/dry appliance.

The shaver may

be cleaned under

warm water.

Trim

Cleaning and Care

NOTE: When cleaning your shaver,

make sure the shaver is turned off

and disconnected from the power

adapter.

For optimal shaver performance,

clean your shaver after each use.

CAUTION!

• Shaver can be placed under

running water for cleaning only.

Never submerge the shaver in

water.

1. Slide trimmer release button

up to engage the trimmer.

(Diagram F)

2. Trim long, difficult hairs and

side burns.

(Diagram G)

3. Close trimmer by sliding the

button down. (Diagram H)

Daily Cleaning:

1. Pull off Stubble comb/Head guard, if

using, and rinse attachment.

2. Grasp the front

and back of the

cutter assembly

and pull away from

the shaver body.

(Diagram I)

3. Tap the stubble

from the foils and

cutters.

4. Use the cleaning

brush to sweep

any loose hairs

from the cutters,

hairpocket, and

trimmer. Pay

close attention

to cleaning out

the corners and

crevices inside

the hairpocket.

(Diagrams J–K)

5. Rinse head under running water.

6. Gently dry with towel or leave

disassembled to air dry.

7. Replace hair pocket assembly when

dry. (Diagram L)

8. Reattach the Stubble comb/Head

guard to protect the shaving head

until next use.

When your rechargeable shaver reaches

the end of its useful life, the batteries

must be removed from the shaver and

recycled or disposed of properly in

accordance with your state and local

requirements. If this is not required by

law, you may elect to dispose of the

shaver with the batteries.

This device uses one of the following

types of rechargeable batteries: nickel

metal hydride (NiMH), nickel cadmium

(Ni-Cd) or Lithium Ion (Li-Ion) (see

included battery for indication of type).

CAUTION: ALL RECHARGEABLE

BATTERIES MUST BE RECYCLED

OR DISPOSED OF IN ACCORDANCE

WITH APPLICABLE STATE AND LOCAL

REGULATIONS. DO NOT PUT IN FIRE

OR MUTILATE, AS THE BATTERY

MAY BURST OR RELEASE TOXIC

MATERIALS. DO NOT SHORT-CIRCUIT,

AS THIS MAY CAUSE BURNS.

Product Disposal

To Remove the Rechargeable Battery:

1. Remove phillips head screw at the

base of the shaver.

2. Pry the outer sleeve down off the

shaver handle.

3. Pry the back housing cover off the

shaver.

4. Remove screws from inner housing

and open inner housing to expose

the batteries.

5. Snip the battery wires and remove

batteries.

6. Dispose of battery properly.

Spectrum Brands, Inc. is a proud partici-

pant in the EPA-approved Rechargeable

Battery Recycling Call2RecycleTM,

which collects and recycles these bat-

teries at the end of their useful life

when taken out of services in the United

States.

The RBRC® program provides a conve-

nient alternative to placing used batter-

ies into the trash or the municipal waste

stream, which may be illegal in your

area. Please call 1-800-8-BATTERYTM

or visit www.call2recycle.org for infor-

mation on LiFePO4 battery recycling and

disposal bans/restriction in your area.

Spectrum Brands, Inc.'s involvement

in this program is part of our commit-

ment to preserving our environment and

conserving our natural resources.

Maintain your shaver’s peak

performance! Keep your shaver

performing like new!

• Because your satisfaction is

important to us, we want to make

it simple for you to keep your new

shaver performing at its peak.

• For the best possible shave, it is

necessary to replace the heads and

cutters on your shaver every 12

months.

• Remington makes this easy!

Two easy ways to order!

1. Call!

U.S. residents call 800-392-6544

2. Order Online at

RemingtonProducts.com

Warranty

How to Order Shaver Accessories

Please refer to the shaver compari-

son and features chart near the

front of this manual that lists the

correct replacement part number

for your shaver.

It is very important to replace your

head and cutters when necessary to

ensure a close, comfortable shave

without irritation. We recommend they

be replaced every 12 months. Here

are some signs of head and cutter

wear, indicating that replacement

is needed:

• Irritation: As the heads get

excessively worn you may

experience some skin irritation.

This would be especially noticeable

when you apply moisturizing lotion.

• Pulling: When the cutters wear you

may feel a sense of pulling and a

loss of closeness when you shave.

This is an indication that it is time

to replace your heads and cutters.

100-240 VAC, 50/60 Hz

TYPE: F20A

Questions or comments:

Call 800-736-4648 in the U.S. or visit RemingtonProducts.com

Dist. by: Spectrum Brands, Inc., Middleton, WI 53562

REMINGTON is a Registered Trademark of Spectrum Brands, Inc.

26158

Made in China.

T22-7001219-A

Contains a

listed adapter

IMPORTANT SAFETY INSTRUCTIONS -

SAVE THESE INSTRUCTIONS

DANGER - TO REDUCE THE RISK OF

FIRE OR ELECTRIC SHOCK, CAREFULLY

FOLLOW THESE INSTRUCTIONS

For connection to a power supply not in the U.S.A., use an attachment plug adapter

of the proper configuration for the power outlet.

Power Adaptor

Lifetime Warranty

Spectrum Brands, Inc. warrants this product against any defects that are due to

faulty material or workmanship for the life of the product. This warranty does not

include damage to the product resulting from accident or misuse.

If the product should become defective, we will replace it free of charge. Return

your product with your name, address and day time phone number to: Remington

Returns Center, 507 Stokely Dr., P.O. Box 1, Deforest, WI 53532. For more informa-

tion call 800-736-4648 in the US or

800-268-0425 in Canada.

Warranty excludes:

• The heads and cutters are not included in lifetime warranty

This warranty does not cover products damaged by the following:

• Accident, misuse, abuse or alteration of the product

• Servicing by unauthorized persons

• Use with unauthorized accessories

• Connecting it to incorrect current and voltage

• Wrapping cord around appliance causing premature wear & breakage

• Any other conditions beyond our control

No responsibility, obligation, or liability is assumed for the installation or mainte-

nance of this product.

SPECTRUM BRANDS, INC. SHALL NOT BE RESPONSIBLE FOR ANY

INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE

USE OF THIS PRODUCT. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT

LIMITED TO IM PLIED WARRANTIES OF FITNESS AND MERCHANTABILITY, ARE

LIMITED IN DURATION TO THE LIFE OF THE PRODUCT.

This warranty gives you specific legal rights and you may also have other rights

which vary from state to state or province to province. Some states do not allow

the exclusion or limitation of incidental, special or consequential damages.

This warranty shall not be valid where it is contrary to U.S. and other appli-

cable laws, or where the warranty would be prohibited under any economic

sanctions, export control laws, embargos, or other restrictive trade mea-

sures enforced by the United States or other applicable jurisdictions. This

includes, without limitation, any warranty claims implicating parties from,

or otherwise located in, Cuba, Iran, North Korea, Syria and the disputed

Crimea region.

Spectrum Brands, Inc. Money-back Offer

If within 30 days after you have purchased your Remington branded product, you

are not satisfied and would like a refund, return it with the sales slip indicating

purchase price and date of purchase to the retailer from whom it was purchased.

Spectrum Brands, Inc. will reimburse all retailers who accept the product within 30

days from the date of purchase. If you have any questions concerning the money-

back guarantee, please call 800-736-4648 in the US.

Remington 60-Day Money Back Guarantee*

If within 60 days after purchasing any Remington branded product, you are not

completely satisfied and would like a refund, return it with the original dated

sales receipt directly to Remington and receive a full refund.** For questions

concerning the money-back guarantee, please call 800-736-4648 in the US.

*Applies to US and Canadian customers’ returns only.

**Terms and conditions apply.

Terms and Conditions

1. Refund will be in the form of a check issued in US Dollars and will be provided

only if all Terms and Conditions are met.

2. The following items must be returned to Remington and postmarked no later

than 60 days after purchase of the Remington branded Men’s Shave and Groom

product:

a. The Remington product;

b. The original sales receipt indicating price and date purchased; and

c. The completed 60-day money back guarantee form located at

RemingtonProducts.com/60day.

3. In addition, Remington, in its discretion, must determine that the returned product

was used in accordance with the instruction booklet (included with the product

at the time of purchase).

4. Returns should be mailed prepaid (no collect returns accepted) to:

Remington 60-Day MBG

507 Stokely Drive, Box 1

DeForest, WI 53532

5. Refund does not include postage costs for the return of the product, but will

include applicable taxes paid by customer, if any.

6. No responsibility will be accepted for late, lost, stolen, misdirected or damaged

product.

7. Please allow 4-6 weeks to receive your refund by check.

Questions or comments: Call 800-736-4648 in the U.S. or visit

RemingtonProducts.com.