Ryobi AP1305 Bruksanvisning
Les nedenfor 📖 manual på norsk for Ryobi AP1305 (60 sider) i kategorien planerer. Denne guiden var nyttig for 4 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/60
TABLE OF CONTENTS
****************
General Safety Rules ....................... 2-3
Specific Safety Rules ...................... 3-4
Symbols ...............................................5
Electrical .......................................... 6-7
Glossary of Terms ................................ 8
Features ...............................................9
Assembly ..................................... 10-11
Operation ..................................... 12-14
Adjustments ......................................15
Maintenance ................................ 16-17
Troubleshooting .................................18
Parts Ordering / Service ...... Back Page
TABLE DES MATIÈRES
****************
Règles de sécurité générales .......... 2-3
Règles de sécurité particulières ...... 3-4
Symboles ............................................. 5
Caractéristiques électriques ............ 6-7
Glossaire ..............................................8
Caractéristiques ..................................9
Assemblage ................................. 10-11
Utilisation ..................................... 12-14
Réglages ............................................15
Entretien ...................................... 16-17
Dépannage ........................................18
Commande de pièces /
réparation .......................... Page arrière
ÍNDICE DE CONTENIDO
****************
Reglas de seguridad generales ....... 2-3
Reglas de seguridad específicas .... 3-4
Símbolos .............................................5
Aspectos eléctricos ......................... 6-7
Glosario de términos ...........................8
Características ....................................9
Armado ........................................ 10-11
Funcionamiento ........................... 12-14
Ajustes ............................................... 15
Mantenimiento ............................. 16-17
Corrección de problemas .................. 18
Pedidos de piezas /
servicio ........................... Pág. posterior
OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
12-1/2 in. THICKNESS PLANER
PLANEUSE À RABOTAGE
DE 317,5 mm (12-1/2 po)
CEPILLO REGRUESADOR
DE 317,5 mm (12-1/2 pulg.)
AP1305
WARNING: To reduce the
risk of injury, the user must read and
understand the operator’s manual
before using this product.
SAVE THIS MANUAL FOR
FUTURE REFERENCE
ADVERTENCIA: Para reducir
el riesgo de lesiones, el usuario debe leer
y comprender el manual del operador
antes de usar este producto.
AVERTISSEMENT :
Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation avant
d’employer ce produit.
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
Page 2 — English
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Read the operator’s
manual carefully. Learn the tool’s applications and limita-
tions as well as the specific potential hazards related to
this tool.
GUARD AGAINST ELECTRICAL SHOCK BY PREVENT-
ING BODY CONTACT WITH GROUNDED SURFACES.
For example: pipes, radiators, ranges, refrigerator enclo-
sures.
KEEP GUARDS IN PLACE and in good working order.
REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents. DO NOT leave tools or pieces
of wood on the tool while it is in operation.
DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools in damp or wet locations or expose
to rain. Keep the work area well lit.
KEEP CHILDREN AND VISITORS AWAY. All visi-
tors should wear safety glasses and be kept a safe
distance from work area. Do not let visitors contact
tool or extension cord while operating.
MAKE WORKSHOP CHILDPROOF with padlocks and
master switches, or by removing starter keys.
DON’T FORCE TOOL. It will do the job better and safer
at the feed rate for which it was designed.
USE RIGHT TOOL. Don’t force the tool or attachment to
do a job it was not designed for. Don’t use it for a purpose
not intended.
USE THE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. Use only a cord heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage result-
ing in loss of power and overheating. A wire gauge size
(A.W.G.) of at least 12 is recommended for an extension
cord 50 feet or less in length. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier
the cord.
DRESS PROPERLY. Do not wear loose clothing, gloves,
neckties, or jewelry. They can get caught and draw you
into moving parts. Also wear protective hair covering to
contain long hair.
ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses, they are NOT safety glasses.
SECURE WORK. Use clamps or a vise to hold work when
practical. It’s safer than using your hand and frees both
hands to operate tool.
DON’T OVERREACH. Keep proper footing and
balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for better and safer performance. Follow in-
structions for lubricating and changing accessories.
DISCONNECT TOOLS. When not in use, before
servicing, or when changing attachments, blades, bits,
cutters, etc., all tools should be disconnected.
AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in any tool.
USE RECOMMENDED ACCESSORIES. Consult the
operator’s manual for recommended accessories. The
use of improper accessories may risk injury.
NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is unintentionally
contacted.
CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
USE THE RIGHT DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of rotation of blade
or cutter only.
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
THE POWER OFF. Don’t leave tool until it comes to a
complete stop.
PROTECT YOUR LUNGS. Wear a face or dust mask if
the cutting operation is dusty.
PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
DO NOT ABUSE CORD. Never yank cord to disconnect
from receptacle. Keep cord from heat, oil, and sharp
edges.
USE OUTDOOR EXTENSION CORDS. When tool
is used outdoors, use only extension cords with
approved ground connection that are intended for use
outdoors and so marked.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
INSPECT TOOL CORDS PERIODICALLY. If dam-
aged, have repaired by a qualified service technician at
an authorized service facility. The conductor with insula-
tion having an outer surface that is green with or without
yellow stripes is the equipment-grounding conductor. If
Page 3 — English
SPECIFIC SAFETY RULES
GENERAL SAFETY RULES
repair or replacement of the electric cord or plug is neces-
sary, do not connect the equipment-grounding conductor
to a live terminal. Repair or replace a damaged or worn
cord immediately. Stay constantly aware of cord location
and keep it well away from the rotating blade.
INSPECT EXTENSION CORDS PERIODICALLY and
replace if damaged.
GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole
electrical receptacle.
CHECK WITH A QUALIFIED ELECTRICIAN or service
personnel if the grounding instructions are not completely
understood or if in doubt as to whether the tool is properly
grounded.
USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire
extension cords that have 3-prong grounding plugs and
3-pole receptacles that accept the tool’s plug.
DO NOT MODIFY the plug provided. If it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
STAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
NEVER TOUCH BLADE or other moving parts during
use.
NEVER START A TOOL WHEN ANY ROTATING
COMPONENT IS IN CONTACT WITH THE WORKPIECE.
DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
WHEN SERVICING use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
USE ONLY RECOMMENDED ACCESSORIES listed in
this manual or addendums. Use of accessories that are
not listed may cause the risk of personal injury. Instruc-
tions for safe use of accessories are included with the
accessory.
DOUBLE CHECK ALL SETUPS. Make sure blade is tight
and not making contact with tool or workpiece before
connecting to power supply.
NEVER PERFORM THE PLANING OPERATION with
the cutter head, dust guide, or dust hood removed.
NEVER MAKE A PLANING CUT deeper than 1/8 in.
DO NOT PLANE MATERIAL shorter than 14 in. or
narrower than 3/4 in.
MAINTAIN THE PROPER RELATIONSHIP between the
infeed and outfeed surfaces and the cutter head blade
path.
SUPPORT THE WORKPIECE ADEQUATELY at all times
during operation; maintain control of the work at all times.
NEVER FEED THE WORK from the rear of the planer.
DO NOT ATTEMPT TO PERFORM an abnormal or little
used operation without the use of sturdy and adequate
jigs, fixtures, stops, and the like.
NEVER plane more than one piece at a time. DO NOT
PLANE more than one workpiece on the planer table at
a time.
BEFORE STARTING UP, recheck to make certain all
holding screws are tight.
STOP THE MACHINE and recheck the hex head bolts
and blades for tightness after about 50 hours of operation.
DO NOT FORCE FEED THE WORKPIECE through the
machine. Let the planer apply the proper feed rate.
CHECK THE FEED ROLLERS occasionally to be sure
there are no chips or sawdust between any components.
PLANE ONLY SOUND LUMBER; there should be no
loose knots and as few tight knots as possible. Make
sure the workpiece is free from nails, screws, stones, or
other foreign objects that could break or chip the blades.
NEVER STAND DIRECTLY IN LINE with either the infeed
or outfeed sides. Stand off to one side.
MAKE SURE THE BLADES ARE ATTACHED as
described in the operation section. The blades are sharp
and can easily cut your hand. Use caution in handling the
blades and cutter head guard.
Produkspesifikasjoner
| Merke: | Ryobi |
| Kategori: | planerer |
| Modell: | AP1305 |
Trenger du hjelp?
Hvis du trenger hjelp med Ryobi AP1305 still et spørsmål nedenfor, og andre brukere vil svare deg
planerer Ryobi Manualer
30 August 2025
30 August 2025
30 August 2025
planerer Manualer
- planerer DeWalt
- planerer AEG
- planerer Milwaukee
- planerer Worx
- planerer Ozito
- planerer Hikoki
- planerer Parkside
- planerer Trotec
- planerer Scheppach
Nyeste planerer Manualer
30 August 2025
28 August 2025
28 August 2025
27 August 2025
26 August 2025
25 August 2025
25 August 2025
18 August 2025
13 August 2025
7 August 2025