Techly I-CASE TRAY-ORG800 Bruksanvisning
Techly
Ikke kategorisert
I-CASE TRAY-ORG800
Les nedenfor 📖 manual på norsk for Techly I-CASE TRAY-ORG800 (2 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 20 personer og ble vurdert med 3.5 stjerner i gjennomsnitt av 10.5 brukere
Side 1/2
WWW.TECHLY.COM
CABLE MANAGEMENT TRAY
USER'S
MANUAL
INTRODUCTION
This rack cable management system is a smart solution for tidying up cables and neatly managing
cabling inside a 19” rack.
Ideal for keeping the wiring tidy and clean, essential for checking and replacing the cables.
FUNCTION DESCRIPTION
Clear identification:
With layer identification, connection relationship identification, line direction identification
INSTALLATION AND OPERATION INSTRUCTIONS
Item Name Picture Qty Remark
Cable
Management
1
M6*16 Cabinet
Screws
2
Used for fixing the front
of the cable tray
M6*40 Cabinet
Screws
2
Used for fixing the side
of the cable tray
Spacers*
2
Used for fixing the side
of the cable tray for 800
and 1000mm versions
Cable
Channel*
6
For cables routing, only for
800 and 1000mm versions
Connecting
Rod*
2
Used for cabinets with a
depth of 800mm / 1000mm
Foam Stick
1
Auxiliary tools to ensure
that the bending radians
of the network cables are
consistent
Cable Tie
2
Used for cabinets with a
depth of more than 800mm
Low cost of repeated cable management:
When a line is messy, it does not affect the overall
line direction, convenient and quick recovery
Standardized and cost-effective construction
One-to-one channel routing, non-professional
can achieve standardized wiring
STRUTTURA DEL
Connection
Relationship
Identification
Line Direction
Identification
Layer
Identification
• Insert the cable management system into the rack cabinet in the direction indicated by the arrow in
figure 1
• Fix to the front rails of the rack in the desired position using M6x16 screws
• Secure laterally to the rack using the M6x40 screws that will lock the cable management tray to the
rear rails** (figure 2)
• Insert the cable in the desired position and slide it into the guide until it comes out on the other side
of the panel; it is possible to insert the cable both from the front and from the side holes
• After cable installation, it is possible to block the cable by inserting the rubber cable clamp on the
front hole of the organizer
• For more careful and precise cable management, you can use the supplied foam tube to create an
even bend for all cables. After extracting the cable from the hole, pass it on the surface of the foam
stick and connect it to the equipment to give the correct bending radius, once this step has been
carried out for all the cables, remove the foam stick
• One or more organizers can be used within the same rack cabinet depending on the installation
requirements
** For models with depths of 800 and 1000mm it is necessary to install the connection bracket using
the 4 screws supplied; to fix the bracket to the rail, use the spacers and cable ties provided
PACKING LIST
PRODUCT STRUCTURE AND COMPONENT NAMES
Cable Management
Connecting Rod
Support Column
Cable Channel
Cabinet Screws
Figure 1 Figure 2
Foam Stick Cable Channel
Support Column
Buckle Position
Cabinet
Screws
* Only for 800 and 1000mm deep version, not included for 600mm version
Produkspesifikasjoner
| Merke: | Techly |
| Kategori: | Ikke kategorisert |
| Modell: | I-CASE TRAY-ORG800 |
Trenger du hjelp?
Hvis du trenger hjelp med Techly I-CASE TRAY-ORG800 still et spørsmål nedenfor, og andre brukere vil svare deg
Ikke kategorisert Techly Manualer
8 April 2025
29 Desember 2024
Ikke kategorisert Manualer
- Hawk-Woods
- Biostar
- Bright Starts
- FireAngel
- XCell
- Gamma
- Conair
- Winix
- Proclip
- Grasslin
- MBM
- Advance
- SmallRig
- Sunding
- Dualit
Nyeste Ikke kategorisert Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025