Adj X-MOVE LED 25R Bruksanvisning

Adj Ikke kategorisert X-MOVE LED 25R

Les nedenfor 📖 manual på norsk for Adj X-MOVE LED 25R (12 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/12

American DJ - www.americandj.com - X-Move LED 25R Instruction Manual Page 2®

X-Move LED 25R General Information

Unpacking: Thank you for purchasing the X-Move LED 25R by Amer-

ican DJ . Every X-Move LED 25R has been thoroughly tested and has ®

been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your xture for any

damage and be sure all equipment necessary to operate the unit has

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Please do not return this unit to your dealer without con-

tacting customer support rst.

Introduction: The X-Move LED 25R is a nine channel DMX intelligent,

moving head, mini LED fixture. The X-Move LED 25R can operate as a

stand alone fixture or in a Master/Slave configuration. The X-Move LED

25R has three operating modes; a sound active, show mode, DMX

controlled. For best results use fog or special effects smoke to enhance

the beams projections.

Customer Support: American DJ provides a toll free customer ®

support line, to provide help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: support@americandj.com

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

User Instructions

5/12

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break o the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 20 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits

a marked change in performance.

X-Move LED 25R Safety Precautions

American DJ - www.americandj.com - X-Move LED 25R Instruction Manual Page 4American DJ - www.americandj.com - X-Move LED 25R Instruction Manual Page 3 ®®

• DMX-512 Protocol Compatible (Nine DMX Channels)

• 8 Colors + White

• 6 Rotating, Replaceable Gobos + Spot

• 3 Operating Modes - Sound Active, Show Mode, & DMX Control

• Internal Microphone

• Digital Display for Address and Function Setting

• UC3 Controller (Not Included)

• 4 Preprogrammed Shows

X-Move LED 25R Features

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ .®

During operation the housing may become extremely hot. Avoid

touching the unit with bare hands while in use.

American DJ® will not accept any liability for any resulting damages

caused by the non-observance of this manual or any unauthorized

modication to this unit.

X-Move LED 25R Handling Precautions

X-Move LED 25R Warranty Registration

The X-Move LED 25R carries a 3 year (1095 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase

and warranty. You may also register your product online at www.

americandj.com. All returned service items whether under warranty or

not, must be freight pre-paid and accompany a return authorization

(R.A.) number. If the unit is under warranty you must provide a copy

of your proof of purchase invoice. Please contact American DJ® cus-

tomer support for a R.A. number.

To optimize the performance of this product, please read these

operating instructions carefully to familiarize yourself with the basic

operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please

keep this manual with the unit, for future reference.

X-Move LED 25R General Instructions

American DJ - www.americandj.com - X-Move LED 25R Instruction Manual Page 6American DJ - www.americandj.com - X-Move LED 25R Instruction Manual Page 5 ®®

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

X-Move LED 25R.The American DJ X-Move LED®

25R is available in

a 120v and 220v version. Because line voltage may vary from venue

to venue, you should be sure your unit voltage matches the wall outlet

voltage before attempting to operate you xture. Also be sure to only

use the included I.E.C. power cable supplied with the unit, this cable

matches the voltage and current requirements of the unit.

DMX-512: -DMX is short for Digital Multiplex. This is a universal pro

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of dierent manufactures to be linked together and operate from a

single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX

and Master/Slave Operation): The X-Move LED

25R can be controlled via DMX-512 protocol. The

X-Move LED 25R is a nine channel DMX unit. The

DMX address is set electronically using the con-

trols on the front panel of the unit. Your unit and

your DMX controller require a approved DMX-512

110 Ohm Data cable for data input and data output

(Figure 1). We recommend Accu-Cable DMX cables. If you are making

X-Move LED 25R Set Up

Figure 1

your own cables, be sure to use standard 110-120 Ohm shielded cable

(This cable may be purchased at almost all professional sound and

lighting stores). Your cables should be made with a male and female

XLR connector on either end of the cable. Also remember that DMX

cable must be daisy chained and cannot be split.

X-Move LED 25R Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground

XLR Male Socket

XLR Pin Conguration

3 Hot

2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

Termination educes signalr errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

Figure 4

Produkspesifikasjoner

Merke:	Adj
Kategori:	Ikke kategorisert
Modell:	X-MOVE LED 25R
Produkttype:	Disko-spotlight
Innebygd skjerm:	Ja
Opprinnelsesland:	USA
Egnet for innendørs bruk:	Ja
Lampetype:	LED
Levetid, pære:	50000 timer