EXSYS EX-60325 Bruksanvisning

EXSYS Bryter EX-60325

Les nedenfor 📖 manual på norsk for EXSYS EX-60325 (2 sider) i kategorien Bryter. Denne guiden var nyttig for 11 personer og ble vurdert med 5.0 stjerner i gjennomsnitt av 6 brukere

Side 1/2
RJ45 Port
Pin Signal PoE (Mode) Pin Signal PoE (Mode)
1 BI_DA+ VCC+ (A) 5 BI_DC- VCC+ (B)
2 BI_DA- VCC+ (A) 6 BI_DB- VCC- (A)
3 BI_DB+ VCC- (A) 7 BI_DD+ VCC- (B)
4 BI_DC+ VCC+ (B) 8 BI_DD- VCC- (B)
Power LED
PoE LED
6 5
in Daten und Stromversorgung und gibt beide Signale getrennt aus. So können auch nicht PoE-
fähige Ethernet-Endgeräte (IP-Kameras, WLAN Access Points...) an einem PoE-Switch oder
anderen PSE angeschlossen werden und deren Speisung nutzen. Er ist konform zum PoE+
Standard IEEE 802.3at und stellt am Terminal Block zur Speisung des Endgerätes eine Span-
nung von 12VDC mit einer Leistung von max. 20W zur Verfügung. Dank dem robusten Metall-
gehäuse und dem erweiterten Betriebstemperaturbereich von -40°C bis 80°C ist er für eine
Vielzahl von Anwendungen auch in rauen Umgebungen geeignet. Im Lieferumfang ist ein DIN-
Rail Kit (vormontiert) und ein Wandmontagebügel enthalten.
1
BESCHREIBUNG & TECHNISCHE DATEN
AUFBAU
Kompatibilität: Gigabit Ethernet 10/100/1000Base-T
PoE: IEEE 802.3af/at (PoE+)
Ausgang: 12VDC, max. 20W
Betriebssysteme: Alle Betriebssysteme
Anschlüsse: 2x RJ45-Buchse, 1x Terminal Block 12VDC
Lieferumfang: EX-60325, DIN-Rail Kit, Wandmontagehalterung, Anleitung
HARDWARE INSTALLATION
CONNECTORS & LED'S
12V T-Block:
ATTENTION!
Power supply OUTPUT, NO connection for external power
supplies!
Please pay attention to the correct polarity!
Status LEDs:
LED Name Color LED Function
Power Green
On: Power out 12VDC
Off: no Power out
PoE
Green
On: PSE Power in
Off: no PSE Power in
RJ45 Port:
Please read the following installation instructions.
1. Install the EX-60325 on a mounting rail using the DIN-Rail kit or on the wall using the wall
mounting brackets.
2. Connect your Ethernet end device (e.g. IP camera, IP phone...) to the Ethernet downlink
port and the terminal block (pay attention to polarity).
3. Connect your PoE PSE (Power Sourcing Equipment) to the PoE-In port.
4. When all cables are connected correctly, the indicators light up according to the port status
of the LEDs (page 5).
The DIN-Rail Kit is pre-assembled with
two screws on the rear side
To install the wall mount, the DIN-
Rail kit must be replaced by the
mounting bracket
V+
V-
Stromausgang 12V DC
via T-Block
Status LEDs RJ45-Downlink
(Daten)
RJ45-Uplink
(PoE/Daten)
87654321
To clean the unit, use only a dry, lint-free cloth and apply light pressure to remove dirt. Take
care not to leave any fibres of the cloth in the connectors.
Never use a damp or wet cloth for cleaning!
CLEANING
TECHNICAL NOTE
Procedure for STP Cable Grounding
When using shielded cables to connect two Ethernet devices, a ground loop may occur if the
shielding on the cables generates an additional grounding connection path. This can cause
ground current to flow through to the Ethernet ports and damage the devices. If it is necessary
to use shielded cables, we recommend using a metallic RJ45 connector on one end and a non-
metallic connector on the other end. Alternatively, a patch panel can be used in between the
two devices to prevent ground loops from occurring.
For connections over short distances (e.g., between two devices installed in the same cabinet),
both ends of the shielded cable can be referenced to the same grounding point. Therefore, in
this case, it is acceptable to use a shielded cable with metallic RJ45 connectors on both
devices.
E 6032
Anleitun
Vers. 1.1 / 20.12.24
Switzerland:
EXSYS Vertriebs GmbH
Dübendorfstrasse 17
8602 Wangen
www.exsys.ch
Germany:
EXSYS Vertriebs GmbH
Industriestrasse 8
61449 Steinbach
www.exsys.de
Italy:
EXSYS Italia Srl
Via Belvedere, 45/B
I-22100 Como
www.exsys.it

Produkspesifikasjoner

Merke: EXSYS
Kategori: Bryter
Modell: EX-60325

Trenger du hjelp?

Hvis du trenger hjelp med EXSYS EX-60325 still et spørsmål nedenfor, og andre brukere vil svare deg