Festo DADM-CK-90-12 Bruksanvisning
Festo
Ikke kategorisert
DADM-CK-90-12
Les nedenfor 📖 manual på norsk for Festo DADM-CK-90-12 (2 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 22 personer og ble vurdert med 4.7 stjerner i gjennomsnitt av 11.5 brukere
Side 1/2
Assembly instructions (Original: de)
8059334
1604c
[8059336]
†‡
Indexing conversion kit
DADM-CK
Festo SE & Co. KG
Postfach
73726 Esslingen
Germany
+49 711 347-0
www.festo.com
1. Parts lists
1a. Parts list DADM-CK-65/-90
11768d_1
1 Spacing bolt1)
2 Index plate
3 Stop bolt1)
4 Screw
5 Special grease
LUB-E1
(free of silicone)
(2x)
(1x)
(1x)
(3x)
(1x)
1b. Parts list DADM-CK-140/-220
11768d_1
1 Spacing bolt1)
2 Index plate
3 Stop bolt1)
4 Screw
5 Special grease
LUB-E1
(free of silicone)
(2x)
(1x)
(1x)
(6x)
(1x)
1c. Not in scope of delivery
11768d_25
6 Rotary indexing
table DHTG
7 Rotating plate
8 Clamping ring
9 Screw
(1x)
(1x)
(1x)
(1x)
2. Intended use
Indexing conversion kit DADM-CK:
Conversion of the rotary indexing table 6 to a different spacing.
3. Safety instructions and notes on mounting
Switch off compressed air before mounting work.
Exhausting rotary indexing table 6.
Observe tightening torques ( Section 6).
Information copies
Applicable documents
www.festo.com/sp
Rotary indexing table DHTG operating instructions
Assembly instructions for energy throughfeed DHTG-P4
4. Preparations for mounting
Disassemble the energy throughfeed DHTG-P4 ( applicable documents).
Grease all movable parts of the indexing conversion kit using the
grease 5.
The rotary table 7 must be turning freely.
To unlock:
Pressurise port “A” with minimum 4 bar.
1) With DADM-CK-65-2, DADM-CK-90-2, DADM-CK-140-3, DADM-CK-220-3 there are no spacing
bolts 1 included in the scope of delivery ( Section 7).
5. Mounting
5a. Disassembly of the rotary table 7
7
7
77
11768d_3
Mark the rotary table 7 and
the clamping ring 8 at the
notch (B) that corresponds
to the countersink of the
screw 9.
Untighten screw 9.
11768d_4
Turn open the clamping
ring 8 with the help of
2 cylindrical dowel
pins (C)2)..
Sizes for cylindrical dowel
pins (C):
DHTG-65: 2 x 2m6
DHTG-90 … -220: 2 x 3m6
Remove the caged ball
bearings (D).
11768d_5
Pull the rotary table 7
up and out with the help
of 2 screws (E)3) .
Thread for screws (E):
DHTG-65/-90: M4
DHTG-140: M6
DHTG-220: M8
Turn the rotating plate 7.
5b. Assembly of the index plate 4
4
4
44.
11768d_6
Unscrew screws (F).
11768d_7
Tighten the screws (F) in the
threads (G).
Force away the index
plate (H) from the rotating
plate 7 by means of the
screws (F).
11768d_8
Position the index plate 2
on the rotating plate 7.
Fasten the index plate 2
with the screws 4.
11768d_9
Observe the index holes (I).
Turn the rotating plate 7.
5c. Assembly of the rotary table 7
7
7
77
11768d_14
Check: The index holes (I) are
located above the index
bolts (J).
Place the rotating plate 7
on the rotary indexing ta-
ble 6.
2) The cylindrical dowel pins (C) are not included in the scope of delivery.
3) The screws (E) are not included in the scope of delivery.
11768d_15
Place the ball bearing
cage (D) in the rotary index-
ing table 6.
Tighten the clamping ring 8
by means of the cylindrical
dowel pins (C).
Untighten and remove the
cylindrical dowel pins (C).
11768d_16
Check: The marks on the
rotating plate 7 and on the
clamping ring 8 match at
the notch (B).
Tighten screw 9.
5d. Assembly of spacing bolt 1
1
1
11
11768d_17
Turn open the clamping
component (K) by 1 turn.
Unscrew the stop screw (L).
11768d_18
Unscrew flow control
valve (M).
Untighten screw (N).
Carefully remove the sub-
base (O). Make sure not to
lose the compression
spring (P) and the seals.
11768d_19
Unscrew screws (Q).
Carefully remove the stop
plate (R). Make sure not to
lose the seals.
11768d_20
Remove the split pins (S)
from the hole to their left.
11768d_21
Push the existing split
pins 11) into the holes on
the left ( section 7).
With the split pins insert-
ed 11):
Position the compression
spring (P) in the hole of the
sub-base (O).
Without the split pins 11) in-
serted:
Remove the compression
spring (P)4) .
Check: Correct fit of the seals.
Fasten the sub-base (O) us-
ing screws (N).
11768d_22
4) Without the split pin 1 mounted, no counter pressure is acting on the compression
spring (P), which causes function failure of the rotary indexing table 6.
Screw in and tighten the
throttle valve (M).
11768d_23
Check: Correct fit of the seals.
Fasten the stop plate (R) us-
ing the screws (Q).
11768d_24
Screw in the existing stop
bolt 3 ( Section 7).
Check: The required cushion-
ing is achieved.
Tighten the clamping com-
ponent (K).
Pressurise the rotary indexing table 6.
The rotary table must not turn freely.
To lock:
Pressurise port “B” with minimum 4 bar.
If the rotary table 7 is still rotating freely:
Manually turn the rotary table 7 until the index bolts (I) engage.
6. Screw sizes and tightening torques MA
5)
DADM-CK- 65 90 140 220
(K) Clamping
component
ß 2.5 4
[Nm]
0.8 2.5
(M) Flow
control valve
GRLA-M5-B GRLA-G1/8
[Nm]
1.5 5.5
(N) Screw M4x16 M6x16 M6x25
[Nm]
3 10
(Q) Screw M4x16 M5x16 M6x16 M6x20
[Nm]
1.5 3 6
4 Screw M4x8 M5x12 M5x16 M6x16
[Nm]
2 4 7
9 Screw M3x6
[Nm]
0.6
7. Lengths of the split pins 1
1
1
11 and stop bolts 3
3
3
331)
DADM-CK- 65 90 140 220
Spacing Pin
2 1 [mm]
————
3 [mm]
12 12 — —
3 1 [mm]
11.31 15.71 — —
3 [mm]
23.3 28 14 19
4 1 [mm]
16.96 23.56 12.57 25.13
3 [mm]
29 35.5 26.5 44.1
6 1 [mm]
22.62 31.42 25.13 50.27
3 [mm]
34.6 43.5 39 69.3
8 1 [mm]
25.45 35.34 31.42 62.83
3 [mm]
37.5 47.5 45.5 81.8
12 1 [mm]
28.27 39.27 37.7 75.4
3 [mm]
40.3 51.5 51.5 94.4
24 1 [mm]
31.1 43.2 43.98 87.97
3 [mm]
45 55.5 58 107
8. Prior to commissioning
Cushioning setting and commissioning ( applicable document).
5) Tolerances for tightening torques MA without tolerance details
MA , 0.60 … 1.00 Nm: ± 30 %
MA , 1.0 Nm: ± 20 %
5
1
2
3
4
5
1
2
3
4
8
7
9
B
8
C
D
7
E
F
F
G
H
7
7
2
4
I
7
J
I
7
6
D
6
8
B
9
7
K
L
M
N
P
O
Q
R
S
1
1
6
P
O
1
N
M
R
Q
3
C
6
9
7
8
C
8
Produkspesifikasjoner
| Merke: | Festo |
| Kategori: | Ikke kategorisert |
| Modell: | DADM-CK-90-12 |
Trenger du hjelp?
Hvis du trenger hjelp med Festo DADM-CK-90-12 still et spørsmål nedenfor, og andre brukere vil svare deg
Ikke kategorisert Festo Manualer
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
31 Mars 2025
31 Mars 2025
Ikke kategorisert Manualer
- Nokia
- Elkay
- Crathco
- BodyCraft
- Safety 1st
- Eero
- Klark Teknik
- Block
- Platypus
- Bright Starts
- OSO
- EnOcean
- Osram
- Senal
- Petkit
Nyeste Ikke kategorisert Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025