Festo DADM-TK-220 Bruksanvisning
Festo
Ikke kategorisert
DADM-TK-220
Les nedenfor 📖 manual på norsk for Festo DADM-TK-220 (2 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 37 personer og ble vurdert med 4.1 stjerner i gjennomsnitt av 19 brukere
Side 1/2
Assembly instructions (Original instructions)
8072099
2017-05d
[8072101]
†‡
Reciprocating motion kit
DADM-TK
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
1. Applicable documents
All available documents for this product www.f
esto.com/pk
Operating instructions for rotary indexing table 5
2. Safety
Observe the safe
ty information ( Applicable documents).
Comply with tightening torques ( Table).
3. I
ntended use
Recip
rocating motion kit DADM-TK:
Conversion of the rotary indexing table DHTG to reciprocating motion.
4. Scope of delivery
11377d_1
1 Shock absorber
2 Stop pin with O-ring
3 Retaining ring
DIN 472
4 Flat seal
(1x)
(4x)
(1x)
(4x)
5. Not in scope of d
e
livery
1137
7d_12
5 Rotary indexing
table DHTG
(B) Stop plate
(H)
Shock absorber
plate
(1x)
(1x)
(1x)
6. Screw sizes and tightening torques M
A
1)
DADM-TK 65 90 140 220
2 Stop pin M4
[Nm] 1.5
(A) Screw M5x16 (3x) M5x16 (5x) M6x16 (5x) M6x20 (5x)
[Nm] 2.9 5.9
(F) Flow control
valve
GRLA-M5-B GRLA-1/8-QS-8-D
[Nm] 1.5 5.5
(G) Screw M4x16 (4x) M4x16 (5x) M6x16 (6x) M6x25 (6x)
[Nm] 2.9 9.9
1)
Tolerance for tightening torques M
A
without indication of tolerance ± 20 %
7. Preparations for mounting
Unlock rotary indexing table 5 ( Applicable documents).
To unlock:
Pressurize the supply port A with at least 4 bar.
The rotary table can be turned freely.
Switch off compressed air.
Exhausting the rotary indexing table.
8. Mounting
11
37
7d
_6
Unscrew screws (A).
Remove stop plate (B).
11377d_13
Check stop plate (B).
The stop plate (B) contains
drill holes (E) or threads (E).
– For drill holes (E)
Section 8a.
– For threads (E)
Section 8b.
8a. For drill h
o
les (E)
11377d_25
Remove O-rings (C) from
the drill holes (D).
1137
7d_26
Place two seals 4 on
the drill holes (D).
11377d_9
Fasten the stop plate (B)
using the screws (A).
11377d_2
Unscrew flow control
valve (F).
Unscrew screws (G).
Remove shock absorber
plate (H).
11377d_3
Remove O-rings (J) from
the drill holes (K).
11377d_4
Place two seals 4 on
the drill holes (K).
Turn the rotary table.
Left drive piston (L) comes
forward
2
)
.
Push the shock absorber 1
into the drive piston (L).
Fasten the shock
absorber 1 with the
retaining ring 3.
Check remaining O-rings
for correct fit.
11377d_5
Fasten shock absorber
plate (H)
3)
with the
screws (G).
Screw throttle valve (F)
in tightly.
11377d_10
Remove the plugs (M)
and (N).
Information
Four stop pins 2 and four O-rings (J) are left over.
8b. For threads (E)
11377d_24
Tighten two stop pins 2
in the threads (E) of the
stop plate (B).
11377d_27
Fasten the stop plate (B)
using the screws (A).
11377d_2
Unscrew flow control
valve (F).
Unscrew screws (G).
Remove shock absorber
plate (H).
11377d_21
Tighten two stop pins 2
in the threads (O) of the
shock absorber plate (H).
11377d_22
Turn the rotary table.
Left drive piston (L)
comes forward
2
)
.
Push the shock absorber 1
into the drive piston (L).
Fasten the shock
absorber 1 with the
retaining ring 3.
Check all O-rings for
correct fit.
11377d_23
Fasten shock absorber
plate (H)
3
)
with the
screws (G).
Screw throttle valve (F)
in tightly.
11377d_10
Remove the plugs (M)
and (N).
Information
Four seals 4 are left over.
2) 3)
9. After mounting
During reciprocating motion, locking is separated from rotation.
Always actuate turn (right/left) and unlock/lock with a controller
accordingly ( Applicable documents).
2)
In case of division > 2 (BG65 and 90)/ > 3 (BG140 and 220):
There is a spacing bolt in front of the left drive piston (L). Remove the spacer bolt during
dismantling and insert it again during mounting.
3)
For division > 2:
When attaching the shock absorber plate, place the small compression spring back into
the drill hole (X) so that it presses on the spacer bolt.
1
3
4
N
M
4
X
2
)
D
1
3
4
B
A
J
K
L
A
B
F
H
G
2
E
B
A
F
H
G
2
B
E
5
B
F
H
G
1
3
L
2
H
O
X
2
)
F
H
G
N
M
K
C
D
H
B
Produkspesifikasjoner
| Merke: | Festo |
| Kategori: | Ikke kategorisert |
| Modell: | DADM-TK-220 |
Trenger du hjelp?
Hvis du trenger hjelp med Festo DADM-TK-220 still et spørsmål nedenfor, og andre brukere vil svare deg
Ikke kategorisert Festo Manualer
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
31 Mars 2025
31 Mars 2025
Ikke kategorisert Manualer
- Summit
- Swann
- Bestway
- Kendall Howard
- Allen & Heath
- TOTO
- Cudy
- Topeak
- EtherWAN
- Scanstrut
- Morel
- Maginon
- PureLink
- Whirlpool
- Metronic
Nyeste Ikke kategorisert Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025