Festo DADP-SP-G9-16-F Bruksanvisning
Festo
Ikke kategorisert
DADP-SP-G9-16-F
Les nedenfor 📖 manual på norsk for Festo DADP-SP-G9-16-F (2 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 12 personer og ble vurdert med 4.8 stjerner i gjennomsnitt av 6.5 brukere
Side 1/2
DADP-SP-G9-...-F
Stop kit
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
Assembly instructions
8195146
2023-07a
[8195148]
8195146
Translation of the original instructions
© 2023 all rights reserved to Festo SE & Co. KG
1
Applicable documents
All available documents for the product
è
www.festo.com/sp.
Document Product Contents
Operating instruction Mini slide DGSS –
Operating instruction Shock absorber DYEF, DYSS –
Tab. 1:
Applicable documents
2 Safety
2.1
Safety instructions
–Only mount the product on components that are in a condition to be safely
operated.
2.2 Intended use
The stop kit in combination with a shock absorber on the mini slide DGSS cush-
ions its extended end position.
3 Additional information
–
Contact the regional Festo contact if you have technical problems
è
www.festo.com.
–
Accessories
è
www.festo.com/catalogue.
4 Product Range Overview
4.1
Scope of delivery
1
2
3
4
Fig.1
1
Screw (2x)
2
Stop (1x)
3
Stop element (1x)
4
Screw (2x)
4.2
Not in scope of delivery
5
6
Fig.2
5
Mini slide (1x)
DGSS
6
Shock absorber (1x)
DYEF-G8/DYSS-G8
5
Product design
Z
Fig. 3:
Product design
Z
Thread for shock absorber
6 Assembly
1
A
B
2
Fig. 4: Pushing in stop
1. Extend the slide[A] manually.
2. Slide the stop into the slot[B].2
3. Insert the screws into the holes of the stop .1 2
4. Slide the stop to the end of the slot[B].2
A
C
1
Fig. 5: Mounting stop
1.
Position the slide[A] so hole[C] is aligned with a screw .1
2.
Tighten the screw . Observe the tightening torque.1
DADP-SP-G9 -6 -10 -16 -20
Screw M2 x 6 M2.5 x 8 M2.5 x 8 M3 x 12
[Nm] 0.3 ±15% 0.5 ±15% 0.7 ±15% 0.9 ±15%
3.
Repeat this process for the second screw .1
C
3
Fig. 6:
Note the stop bar
•
When installing the stop element , note the position of the stop bar[C].3
3
D
A
Fig. 7:
Aligning stop element
1.
Retract the slide[A] manually.
2. Position the upper edge of the stop element at the level of the thread[D].3
3
A
C
Fig. 8:
Attaching stop bar
1. Push the stop element upwards to the stop.3
Ä
The stop bar[C] is in contact with the slide[A].
2. Hold this position.
Produkspesifikasjoner
| Merke: | Festo |
| Kategori: | Ikke kategorisert |
| Modell: | DADP-SP-G9-16-F |
Trenger du hjelp?
Hvis du trenger hjelp med Festo DADP-SP-G9-16-F still et spørsmål nedenfor, og andre brukere vil svare deg
Ikke kategorisert Festo Manualer
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
31 Mars 2025
31 Mars 2025
Ikke kategorisert Manualer
- Start International
- T-Rex
- CatSynth
- Proscan
- Focusrite
- True
- GA.MA
- Ulsonix
- XGIMI
- Kanlux
- Metro
- GLP
- MBM
- Dahua Technology
- Basil
Nyeste Ikke kategorisert Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025