Festo SPAN Bruksanvisning
Festo
Ikke kategorisert
SPAN
Les nedenfor 📖 manual på norsk for Festo SPAN (6 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 54 personer og ble vurdert med 4.3 stjerner i gjennomsnitt av 27.5 brukere
Side 1/6
Pressure sensor SPAN
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
Operating instructions 8035566
2017-11a
[8035568]
Translation of the original instructions
Pressure sensor SPAN English..........................................
For all available product documentation è www.festo.com/pk
1 Product description
The operating instructions describe the entire function range. The function range is
limited, depending on the product variant.
Note
You can find detailed specifications for the product, the device description file
(IODD) with a description of the IO-Link parameters and the declaration of con
formity at: è www.festo.com/sp.
1.1 Overview
1
2
3
456
1 Display
2 Electrical connection
3 Pneumatic connection
4 B-key
5 Edit button
6 A-key
Fig. 1 Representation of other variants can deviate from this
1.2 Characteristics
Characteristic Value Description
Typ e SPAN Pressure sensor
Pressure
measuring range
-B2, -B11, -P025, -P05, -P1, -P2,
-P6, -P10, -P12, -P16, -V025,
-V05, -V1
è Technical data
Supply port R Relative pressure
Pneumatic port -G18, -R18, N18, -M5,
-Q4,
Thread Gx, Rx, NPTx, M5
Push-in connector 4 mm
Thread type
M
F
None
Male thread
Female thread
Electrical
output 1
-PNLK
-PN
Switching output PNP / NPN / IO-Link
PNP / NPN
Electrical
output 2
-PNVBA
-PN
PNP / NPN / 0…10 V / 1…5 V / 4…20 mA
PNP / NPN
Electrical
connection
-L1 Plug connector, design L1
Certificate
+T
Without
With inspection report
Fig. 2
2 Safety
Intended use
The pressure sensor SPAN is intended for monitoring pressure of compressed air
and inert gases in the piping.
General safety information
Only use the product in its original status, without any unauthorised modifications.
Only use the product if it is in an excellent technical status.
The product is intended for use in industrial environments. Measures may need
to be implemented in residential areas for radio interference suppression.
Take into consideration the ambient conditions at the location of use.
Operate the product only with compressed air of the specified air quality class
(è Technical data).
Observe the specifications on the rating plate.
Comply with all applicable national and international regulations.
Disposal
Observe the local specifications for environmentally friendly disposal.
Range of applications and certifications
In connection with the UL marking on the product, the information of this section is
also applicable for compliance with the certification conditions of Underwriters
Laboratories Inc. (UL) for the U.S.A. and Canada.
UL approval information
Product category code QUYX (USA)
QUYX7 (Canada)
File number E322346
Considered standards UL 610101
C22.2 No. 610101
UL mark
Fig. 3
Unit shall be supplied by a power source which complies with the requirements of
a limited-energy circuit in accordance with IEC/EN/UL/CSA 61010-1 or a Limited
Power Source (LPS) in accordance with IEC/EN/UL/CSA 60950-1 or IEC/EN/UL/
CSA 62368-1 or a Class 2 circuit in accordance with NEC or CEC.
3 Function and application
The sensor converts pneumatic pressure values (relative pressure) into electrical
signals, which can be used for control or regulating functions. Measurements are
carried out using a piezoresistive sensor element with a following electronic evalu
ation unit. Interfacing to the higher-level system is provided by 1 or 2 switching
outputs, an optional analogue output and an optional IO-Link interface.
The switching outputs can be configured for monitoring of a threshold value,
a pressure range or a differential pressure. The outputs can be set as PNP or NPN
and normally open (NO) or normally closed (NC). Via the IO-Link interface, process
values can be read out and parameters changed and transmitted to additional
devices.
3.1 Operating statuses
Operating status Function
RUN mode – Basic status after the operating voltage is switched on
– Display of the current measured value
SHOW mode – Display of the current settings
EDIT mode – Setting or modification of parameters
TEACH mode – Acceptance of the current measured value to determine switching
points
Fig. 4
3.2 Switching functions
Threshold value comparator for monitoring of a pressure threshold _|¯
Function NO (normally open) NC (normally closed)
Switching function:
– 1 switching point (SP)
TEACH mode:
– 2 teach-in points (TP1, TP2)
– SP = ½ (TP1+TP2)
TP1 TP2
HY
1
0
Out
p
SP
TP1 TP2
SP
HY
1
0
Out
p
Fig. 5
Produkspesifikasjoner
| Merke: | Festo |
| Kategori: | Ikke kategorisert |
| Modell: | SPAN |
Trenger du hjelp?
Hvis du trenger hjelp med Festo SPAN still et spørsmål nedenfor, og andre brukere vil svare deg
Ikke kategorisert Festo Manualer
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
6 August 2025
31 Mars 2025
31 Mars 2025
Ikke kategorisert Manualer
- Zodiac
- PCE
- ClearOne
- VAIS Technology
- ToughTested
- UDG Gear
- FAR
- Scala
- Adj
- Focusrite
- Peugeot
- Supermicro
- CaviLock
- Kyocera
- AS - Schwabe
Nyeste Ikke kategorisert Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025