EXSYS EX-44062 Bruksanvisning

EXSYS Ikke kategorisert EX-44062

Les nedenfor 📖 manual på norsk for EXSYS EX-44062 (2 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 13 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 7 brukere

Last ned PDF

Side 1/2

6 5 1

Die EX 44062 ist eine PCI Express serielle RS 232 Karte mit 2 seriellen FIFO 16C550 Ports, - - -

für den Anschluss von High Speed seriellen RS 232 Peripherie Geräten (z.B. Terminal, Mo-- -

dem, Plotter usw.). Der serielle PCI Express Bus unterstützt dabei optimal die Leistung des -

schnellen Systembase Chipset. Die Karte gewährleistet so eine sichere Datenübertragung und

exzellente Performance von bis zu 921,6KBaud/s! Sie unterstützt alle PCI Express Slots von p1-x1 -

bis x16. Es ist nicht möglich die I/O Adressen und Interrupts manuell einzustellen, da die Ein-

stellungen der Karte vom System (BIOS) und vom Betriebssystem automatisch vorgenommen

werden. Im Lieferumfang sind zusätzlich zwei Low Profile Bügel enthalten, für den Einbau in

schmale Gehäuse.

BESCHREIBUNG & TECHNISCHE DATEN

JUMPER EINSTELLUNG & ANSCHLÜSSE

Anleitun

Vers. 1.1 / 27.07.20

E 4406

AUFBAU

DRIVER INSTALLATION

Kompatibilität: PCI Express p1-x1 bis x16 -

Betriebssysteme: Windows NT 4.0/ 9x/ 2000/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx/ Linux

Anschlüsse: 2x 9 Pin Seriell Anschluss, 1x 4 Pin Floppy Anschluss

Lieferumfang: 44062, Treiber CD, Anleitung, 2x Low Profile Bügel EX-

Zertifikate:

J5: Anschluss für Strom

vom PC Netzteil

JP4: Jumper für die Stromquelle

(Netzteil oder PCI Express Bus)-

JP1 & JP2: Power auf 9 Pin

Stecker Ein/Aus

JP3: PME

- Ein / Ausschalten

JP5: LPT Ein / Aus

Keine Funktion!

S1 & S2:

9 Pin Stecker

Seriell Anschluss

J5:

1 +5V

2 GND

3 GND

4 +12V

Für AUX Einstellung (JP4) muss J5 mit dem PC Netzteil verbunden

werden! Sonst wird die Karte nicht mit Strom versorgt.

RI = Am Pin 9 liegt das Standard Signal RI (Ring Indicator)

(Werkseinstellung)

5 = Am Pin 9 liegt jetzt eine Spannung von DC5V an

12 = Am Pin 9 liegt jetzt eine Spannung von DC12V an

Die Einstellung der Spannung nehmen Sie mit dem JP4 vor. Dies sollte

aber bei Standard Anwendungen nicht verstellt werden.

JP1 & JP2:

JP4:

Wenn Sie den Jumper JP1 & JP2 auf 5 oder 12 gesetzt haben, können

Sie mit dem Jumper JP4 den Spannungswert einstellen. Es gibt 3

verschiedene Spannungsquellen.

(Nur in Verbindung mit JP1 & JP2 auf 5 oder 12!!!)

X5 - = 5Volt vom PC Netzteil (Werkseinstellung)

X12 - = 12Volt vom PC Netzteil

I12 (Werkseinstellung) = 12Volt vom Mainboard

I12 X12 X5

If you are ready with the jumper settings, please proceed with the following installation instructions.

Because there are large differences between PC’s, we can give you only a general installation

guide. Please refer to your computer s reference manual whenever in doubt.’

1. Turn off the power to your computer and any other connected peripherals.

2. Remove the mounting screws located at the rear and/ or sides panels of your Computer and

gently slide the cover off.

3. Locate an available expansion slot and remove its covers from the rear panel of your comput-

er. Make sure it is the right expansion slot for the card (see card description)

4. Align the card with the expansion slot, and then gently but firmly, insert the card. Make sure

the card is seated and oriented correctly. Never insert the card by force!

5. Then connect the card with a screw to the rear panel of the computer case.

6. Gently replace your computer’s cover and the mounting screws.

DB 9M:

Serial 9 Pin D SUB Connector-

Pin Signal Pin Signal Pin Signal

1 4 DTR 7 RTS CDC

2 RXD 5 GROUND 8 CTS

3 TXD 6 DSR 9 RI

Windows NT 4.0/ 9x/ 2000/ XP/ Vista/ 7/ 8.x/ 10

After completing the hardware installation, the operating system will automatically the card and

install this! If the driver should not be installed automatically, insert the driver CD into you CD-

ROM drive (eg drive D:) and then open the folder „IO/SYSTEMBASE/DRIVERS/PCI(PCIe

Bridge)“. Please select the folder with your operating system and install the driver (see Pic-

ture). Follow the hardware assistant and finish the installation. Restart your PC in Important!

any case after installing the drivers.

JUMPER SETTING & CONNECTORS

HARDWARE INSTALLATION

DRIVER INSTALLATION

DIS = The function PME is disable. (Factory Setting)

ENA = The function PME is enable. Now the card can be activate

the computer through the serial ports.

But this should not be adjusted for standard applications.

ENA | DIS

JP3:

CHECK INSTALLED DRIVER

Open the >Device manager<. Now you should see at and at „Ports (COM & LPT)“

„ “Multifunction Adapter the following new entry's:

If you see this or a similar information the device is installed correctly.

CHANGE PORT NUMBER

If you like to change the port number for example COM3 to COM5, open the „Device Manager”

click at „COM3 Settings Advance”, „ ” and then „ ”. There you can change between COM3 till

COM256.

Windows Server 20xx

After completing the hardware installation, the operating system will automatically the card and

install this! If the driver should not be installed automatically, insert the driver CD into you CD-

ROM drive (eg drive D:) and then open the folder „IO/SYSTEMBASE/DRIVERS/PCI(PCIe

Bridge)“. Please select the folder with your operating system and install the driver (see Picture).

Follow the hardware assistant and finish the installation. Important! Restart your PC in any

case after installing the drivers.

Use the following driver for the following Windows Server Version.

Windows Server 2003 = XP Driver

Windows Server 2008 = VISTA Driver

Windows Server 2008R2 = Windows 7 Driver

Windows Server 2012 = Windows 8.x Driver

Windows Server 2012R2 = Windows 10 Driver

CHECK INSTALLED DRIVER

Open the >Device manager<. Now you should see at and at „Ports (COM & LPT)“

„ “Multifunction Adapter the following new entry's:

If you see this or a similar information the device is installed correctly.

CHANGE PORT NUMBER

If you like to change the port number for example COM3 to COM5, open the „Device Manager”

click at „COM3 Settings Advance”, „ ” and then „ ”. There you can change between COM3 till

COM256.

Linux / SCO Unix

The drivers are located in the following folder on our driver CD:

"IO/SYSTEMBASE/DRIVERS/PCI(PCIe Bridge)/SCO"

Because each individual distribution and kernel version of Linux is different, sadly we cant

provide a installation instruction. Please refer to the installation manual for standard IO ports

from your Unix/Linux version! In some newer versions of Linux the card will even be installed

automatically after starting Linux.

Produkspesifikasjoner

Merke:	EXSYS
Kategori:	Ikke kategorisert
Modell:	EX-44062
Vekt:	120 g
Bredde:	88 mm
Dybde:	66 mm
Vertsgrensesnitt:	PCIe
FIFO (først inn, først ut):	256 B
Utgangsgrensesnitt:	Seriell
Databiter:	5, 6,7, 8
Stoppbiter:	1, 1.5, 2
Produktfarge:	Black, Stainless steel
Seriell grensesnittype:	RS-232
Driftstemperatur (T-T):	0 - 55 °C
Oppbevaringstemperaturomåde (Celsius):	-40 - 75 °C
Bærekraftsertifikater:	RoHS
Støttede Windows operativsystemer:	Ja
Kommunikasjonsserieporter:	2
Relativ luftfuktighet under drift (H-H):	5 - 95
Intern:	Ja
RS-232-tilkobling:	Ja
Plugg inn og spill:	Ja
Støttede Linux operativsystemer:	Ja
Formål:	PC
Utvidelseskort formfaktor:	Lavprofil