NUVO Arabel 60/6967 Bruksanvisning
Les nedenfor 📖 manual på norsk for NUVO Arabel 60/6967 (2 sider) i kategorien Lampe. Denne guiden var nyttig for 28 personer og ble vurdert med 4.7 stjerner i gjennomsnitt av 14.5 brukere
Side 1/2
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING
ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER
IS SHUT OFF.
GENERAL
You don’t need special tools to install this xture. Be sure to follow the steps
in the order given. Under no circumstances should a xture be hung on house
electrical wires, nor should a swag type xture be installed on a ceiling which
contains a radiant type heating system. Read instructions carefully. If you are
unclear as to how to proceed, consult a qualied electrician.
NOTE: Proper wiring is essential for the safe operation of this xture.
FIXTURE ASSEMBLY
Carefully remove the xture from the carton and check that all parts are included
as shown in gure. Be careful not to misplace any of the screws or parts, which
are needed to install this xture.
STEP 1: Thread rods (M) into the coupling (N).
STEP 2: Thread the rods (L) into the rod (M). Carefully pass the wires through
each rod during assembly. Repeat step 2 with rods (K) and (J) until the desired
hanging height is reached.
INSTALLATION
IMPORTANT: Do not attach xture directly to outlet box.
STEP 1: Secure the mounting bar (B) to outlet box with the outlet box screws (A).
Thread the nut (D) onto the nipple (E) so that ve threads are exposed above the
nut (D). Insert the lock washer (C) and thread the nipple (E) into the mounting bar
(B), then secure with the nut (D).
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised dimples
on the mounting bar. Wrap the ground wire from the xture (if supplied) around
the green grounding screw, then connect it to ground wire from the outlet box
(if not xed on the outlet box) using a wire connector (not supplied). If ground wire
from the xture is not supplied, wrap the ground wire (if not xed on the outlet
box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your xture. Identify which
group your xture wire(s) falls into and connect the wires according to the
directions below:
GROUP A:
Connect to Black House Wire
GROUP B:
Connect to White House Wire
BLACK WHITE
* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square
shaped or ridged and the less tracer wire is round in shape or smooth (seen
best when viewed from wire end.)
STEP 3: Take your xture wire(s) from group A and place evenly against the
black wire from the outlet box. Do NOT twist wires together before using wire
connectors.
STEP 4: Fit a wire connector over the wires and screw the connector clockwise
until you feel rmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps 3 and 4 as above, and check again for
a rm connection.
STEP 6: Connect the xture wire from group B to the white wire from the outlet
box in the same manner. Make sure no bare wires can be seen outside wire
connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside outlet box.
Raise canopy (F) allowing the mounting screw (E) to protrude through the hole
in the canopy (F), and secure with nials (G).
STEP 2: Open the link of chain (I), connect it to xture loop (J), and connect it
to the ring (H) and close the link.
STEP 3: Place the glass shades (P) over the sockets (O) and secure with the
retaining rings (Q). Then place the loops (R) over the sockets (O).
STEP 4: Install lamps (S) (not supplied). Do not exceed the maximum capacity
recommended on the socket.
CLEANING
To clean, wipe xture with a soft cloth. Clean glass with a mild soap. Do not
use abrasive materials such as scouring pads or powders, steel wool or a
brasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement
parts. Be sure to use exact wording from illustration when ordering parts.
FIGURE
Line art shown may not exactly match the xture enclosed. However, the installations
do apply to this xture.
La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,
las instalaciones sí aplican para esta pieza.
Les images peuvent ne pas correspondre exactement au luminaire de la boîte.
Par contre, les directives d’installation s’appliquent au luminaire.
INSTALLATION AND SAFETY INSTRUCTIONS
ITEM NO: 60-6967
ARTÍCULO Nº: 60-6967
ARTICLE N°: 60-6967
Produkspesifikasjoner
| Merke: | NUVO |
| Kategori: | Lampe |
| Modell: | Arabel 60/6967 |
Trenger du hjelp?
Hvis du trenger hjelp med NUVO Arabel 60/6967 still et spørsmål nedenfor, og andre brukere vil svare deg
Lampe NUVO Manualer
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
2 April 2025
2 April 2025
2 April 2025
15 Oktober 2024
15 Oktober 2024
Lampe Manualer
- Sonneman
- Dorr
- Intermatic
- ColorKey
- Ozito
- NEO Tools
- Fredrick Ramond
- Makita
- V-Tac
- Casalux
- Physa
- HQ Power
- Nanlite
- EMOS
- Nedis
Nyeste Lampe Manualer
8 April 2025
8 April 2025
6 April 2025
6 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
4 April 2025