NUVO Cordello 60/7884 Bruksanvisning
Les nedenfor 📖 manual på norsk for NUVO Cordello 60/7884 (2 sider) i kategorien Lampe. Denne guiden var nyttig for 32 personer og ble vurdert med 5.0 stjerner i gjennomsnitt av 16.5 brukere
Side 1/2
INSTALLATION AND SAFETY INSTRUCTIONS
ITEM NO: 60-7884
ARTÍCULO Nº: 60-7884
ARTICLE N°: 60-7884
© Copyright 2023 Satco Products, Inc. 4/23 v1.0
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE
WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR
THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this xture. Be sure to follow
the steps in the order given. Under no circumstances should a
xture be hung on house electrical wires, nor should a swag type
xture be installed on a ceiling which contains a radiant type heating
system. Read instructions carefully. If you are unclear as to how to
proceed, consult a qualied electrician.
NOTE: Proper wiring is essential for the safe operation of this xture.
FIXTURE ASSEMBLY
Carefully remove the xture from the carton and check that all parts
are included as shown in gure. Be careful not to misplace any of
the screws or parts, which are needed to install this xture.
STEP 1: Thread rod (K) into lamp body (L). Carefully pass the wires
through each rod during assembly. Repeat step 1 with rods (H), (G)
and (F) until the desired hanging height is reached.
STEP 2: Thread the rod (F) onto coupling (D).
INSTALLATION
IMPORTANT: Do not attach xture directly to outlet box.
STEP 1: Thread mounting screw (A) into the matching hole of
circular strap (B).
STEP 2: Secure the circular strap (B) to outlet box with outlet box
screws (C).
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the mounting bar. Wrap the ground wire from the
xture (if supplied) around the green grounding screw, then connect
it to ground wire from the outlet box (if not xed on the outlet box)
using a wire connector (not supplied). If ground wire from the xture
is not supplied, wrap the ground wire (if not xed on the outlet box)
from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your xture. Identify
which group your xture wire(s) falls into and connect the wires
according to the directions below:
GROUP A:
Connect to Black House Wire
GROUP B:
Connect to White House Wire
BLACK WHITE
* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is
square shaped or ridged and the less tracer wire is round in shape
or smooth (seen best when viewed from wire end.)
STEP 3: Take your xture wire(s) from group A and place evenly
against the black wire from the outlet box. Do NOT twist wires
together before using wire connectors.
STEP 4: Fit a wire connector over the wires and screw the
connector clockwise until you feel rmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps 3 and 4 as above, and check
again for a rm connection.
STEP 6: Connect the xture wire from group B to the white wire
from the outlet box in the same manner. Make sure no bare wires
can be seen outside wire connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside outlet
box. Raise canopy (D) allowing the mounting screw (A) to protrude
through the hole in the canopy (D), and secure with nials (E).
STEP 2: Place the glass shade (O) and the retaining ring (N) over the
socket (P), then secure with the retaining ring (N).
STEP 3: Install lamp bulbs (M) (not supplied). Do not exceed the
maximum capacity recommended on the socket.
CLEANING
To clean, wipe xture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Be sure to use exact wording from illustration
when ordering parts.
FIGURE
Line art shown may not exactly match the xture enclosed. However, the installations
do apply to this xture.
La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,
las instalaciones sí aplican para esta pieza.
Les images peuvent ne pas correspondre exactement au luminaire de la boîte.
Par contre, les directives d’installation s’appliquent au luminaire.
Produkspesifikasjoner
| Merke: | NUVO |
| Kategori: | Lampe |
| Modell: | Cordello 60/7884 |
Trenger du hjelp?
Hvis du trenger hjelp med NUVO Cordello 60/7884 still et spørsmål nedenfor, og andre brukere vil svare deg
Lampe NUVO Manualer
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
2 April 2025
2 April 2025
2 April 2025
15 Oktober 2024
15 Oktober 2024
Lampe Manualer
- Zafferano
- Theben
- Norwell
- Petzl
- Lutec
- Waldmann
- NEO Tools
- Samsung
- Ranex
- Silva
- COLBOR
- V-Tac
- Nicols
- Osram
- Gravity
Nyeste Lampe Manualer
8 April 2025
8 April 2025
6 April 2025
6 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
4 April 2025