BlueBuilt BBMAG1M Bruksanvisning

Les nedenfor 📖 manual på norsk for BlueBuilt BBMAG1M (10 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 32 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/10
Monitor Arm with Mechanical Spring for 1 Monitor
Monitorarm met Mechanische Veer voor 1 Monitor
Bras d’Écran PC avec Ressort Mécanique pour 1 Écran PC
Monitorhalterung mit Mechanischer Federr 1 Monitor
FLYING START.
Whoooo.
934998 - BBMAG1M V1.0
12
13
1
11
3
5
7
9
2
6
8
10
In the box:
1
Swing arm
2
Lift arm
3
VESA plate
4
Base
5
Clamp
6
Clamp attachment
7
Mounting plate
8
Socket head bolts
9
Screw
10
Allen keys 4 and 5 millimetres
11
Screws and washers
SET UP MONITOR ARM.
A helping hand.
30 minutes 1 person 1 coffee
From your own toolbox:
12
Screwdriver
13
Electric drill
EN
EN
Feed-through mount (B)
Drill a hole in your desk and feed the clamp through it.
Clamp mount (A)
Mount your monitor arm to your desk with the clamp.
4
32
STEP 4.
STEP 3B.
Feed-through mount.
STEP 8.
STEP 7.
STEP 5.
STEP 9.
STEP 6.
STEP 10.
Attach the swivel arm
1
to the stand.
Tighten the screw to your liking. e
tighter the screw, the less flexibly the
arm can move.
Place the mounting plate
7
around the
feed-through mount. en twist it into
the stand via the hole until it’s fastened
tightly.
Slide the monitor onto the VESA plate
and screw the bottom screws
11
into the
monitor.
Place your monitor on a rug and insert
the top screws
11
into the monitor.
You can use the washers
11
to make it
sturdier.
Attach the lift arm
2
. Tighten the screw
to your liking.
Slide the cable duct upwards to open it.
Put the cables of your monitor inside and
close it again.
Attach the VESA plate
2
to the monitor
arm and tighten the screw
9
.
Adjust the connector of the monitor
arm with the included hex key
10
to
determine the flexibility.
STEP 3A.
Clamp mount.
STEP 1A.
Clamp mount.
STEP 1B.
Feed-through mount.
STEP 2A.
Clamp mount.
STEP 2B.
Feed-through mount.
Place the clamp on the desk and tighten
the screw upwards until the stand is
fastened tightly.
Suitable for desks with a thickness
between 10 and 50mm.
Take the lid off the stand
4
. Attach the
clamp attachment
6
to the stand and
tighten the bolts
8
.
Suitable for desks with a thickness
between 45 and 80mm.
Twist the disc from the clamp
5
and then
twist and remove the clamp
attachment
6
.
Determine the thickness of your desk.
Depending on that, place the desk
clamp
5
in the upper or lower notches
and tighten the bolts
8
.
Drill a 10mm hole through your desk.
CHECKLIST.
Does the tick.
Check the VESA size of your
monitor. at way, you can
be sure it fits on the monitor
arm. e screw holes of the
VESA plate and your
monitor have to match.
Do you have a question?
Coolblue.nl/en/
customer-service
Coolblue isn’t liable for any
injury, damage, or arguments
with your partner caused by a
wrong installation.
EN
EN
544

Produkspesifikasjoner

Merke: BlueBuilt
Kategori: Ikke kategorisert
Modell: BBMAG1M

Trenger du hjelp?

Hvis du trenger hjelp med BlueBuilt BBMAG1M still et spørsmål nedenfor, og andre brukere vil svare deg




Ikke kategorisert BlueBuilt Manualer

Ikke kategorisert Manualer

Nyeste Ikke kategorisert Manualer